Answer:
14.76
Explanation:
If you put it in the calculator it would show
A dam is used to hold back a river. The dam has a height H = 12 m and a width W = 10 m. Assume that the density of the water is = 1000 kg/m . (a) Determine the net force on the dam. (b) Why does the thickness of the dam increase with depth?
(a) The net force on the dam is approximately 14,126,400 N.
(b) The thickness of the dam increases with depth to counteract increasing hydrostatic pressures and maintain structural stability.
(a) The hydrostatic pressure of the water on the dam determines the net force.
Formula for hydrostatic pressure at a given depth in a fluid:
Pressure = Density x Gravity x Depth
The weight of the water above the dam causes pressure at its base. Based on water density (ρ) of 1000 kg/m³ and gravity acceleration (g) of 9.81 m/s², the dam base pressure is:
Pressure = 117720 N/m² (Pascal)
= 1000 kg/m³ × 9.81 m/s² x 12 m
The dam's base area is 12 m high and 10 m wide:
Area = 12 m x 10 m
= 120 m².
Now we can compute the dam's net force:
Force = Pressure × Area
= 14126400 N (117720 N/m² x 120 m²).
The dam has 14,126,400 N net force.
(b) Water pressure increases with depth, therefore the dam thickens. Because the water above the dam weighs more, it must sustain stronger hydrostatic pressures as it travels deeper. To resist these stresses and prevent structural failure, the dam's thickness must grow with depth. This uniformly distributes pressure and stabilises the dam by holding back water.
Learn more about hydrostatic pressures, here:
https://brainly.com/question/33722056
#SPJ12
The force on the dam is calculated based on the average water pressure and the area of the dam, resulting in an approximate force of 7.08 * 10^5 Newtons. The thickness of the dam increases with depth due to the increased water pressure.
Explanation:(a) To determine the force on the dam we use the concept of physics where the force exerted on the dam by the water is the average pressure times the area of contact (F = pA). Considering the dam has a height H = 12 m and a width W = 10 m, and that the density of the water is 1000 kg/m³, we must consider the average depth of the water, which is half the height of the dam. This is because water pressure increases linearly with depth.
The force is calculated by multiplying the pressure at the average depth (1000 kg/m³ * 9.8 m/s² * 6m) by the area of the dam (10m * 12m), resulting in an approximate force of 7.08 * 10^5 Newtons.
(b) The thickness of the dam increases with depth because the pressure exerted by the water on the dam increases with depth. As the depth of the water increases, so does the pressure it exerts. Therefore, to avoid cracking or collapsing under the increased pressure, the dam is made thick towards the bottom where the pressure is higher.
Learn more about Force on Dam here:https://brainly.com/question/31966157
#SPJ12
a proton moving at 4.00 3 106 m/s through a magnetic field of magnitude 1.70 t experiences a magnetic force of magnitude 8.20 3 10213 n. what is the angle between the proton’s velocity and the field
The angle between the proton's velocity and the magnetic field is approximately 54.8 degrees.
How to find angle between velocity and magnetic field?To find the angle between the proton's velocity and the magnetic field, we can use the formula for the magnetic force experienced by a moving charged particle:
F = q * v * B * sin(θ)
where:
F is the magnitude of the magnetic force,
q is the charge of the particle (in this case, the charge of a proton, which is 1.6 x [tex]10^{-19}[/tex]C),
v is the magnitude of the velocity of the proton,
B is the magnitude of the magnetic field, and
θ is the angle between the velocity and the magnetic field.
Given that the magnitude of the magnetic force (F) is 8.20 x [tex]10^{13}[/tex] N, the charge of a proton (q) is 1.6 x [tex]10^{-19}[/tex] C, the magnitude of the proton's velocity (v) is 4.00 x [tex]10^6[/tex]m/s, and the magnitude of the magnetic field (B) is 1.70 T, we can rearrange the formula to solve for the angle (θ).
sin(θ) = F / (q * v * B)
sin(θ) = (8.20 x [tex]10^{13}[/tex] N) / ((1.6 x [tex]10^{-19}[/tex] C) * (4.00 x [tex]10^6[/tex]m/s) * (1.70 T))
Using a calculator, we can evaluate the right side of the equation:
sin(θ) ≈ 0.805
Now, we can find the angle (θ) by taking the inverse sine (arcsin) of the value:
θ ≈ arcsin(0.805)
Using a calculator, we find:
θ ≈ 54.8 degrees
Therefore, the angle between the proton's velocity and the magnetic field is approximately 54.8 degree
Learn more about magnetic field
brainly.com/question/14848188
#SPJ11
A hand now pushes the same bricks to the right with the force of the same magnitude as in part a. The bricks are moving to the right and speeding up. Systems A, B, and C are the same as in the previous case. As before, there is friction between the bricks and the table. In the spaces provided at right, draw and label separate free-body diagrams for systems A and B. (Ignore vertical forces.) Using the same scales as in part a, draw the acceleration and net force vectors for systems A, B and C. Explain. Using the same scale as in part a, draw the force vectors using the same scale. Explain how you knew to draw the force vectors as you did. Do you agree or disagree with the statement below? Explain. "The force by the hand pushing on system C from the left or from the right are the same. Thus the internal forces are the same in both cases."
Answer:
Explanation:
The free-body diagram for system A includes a force to the left equal in magnitude to the force applied by the hand, as well as a force to the right due to friction with the table.
The free-body diagram for system B is identical to that for system A. The acceleration vector for system A points to the left, while the net force vector points to the right. The acceleration and net force vectors for system B are the same as for system A. The acceleration and net force vectors for system C are also the same as for system A and B.
In this scenario, the force by the hand pushing on system C from the left or right is not the same, since the direction of the force affects the direction of the acceleration. The internal forces, however, are the same in both cases, as they depend only on the interaction between the individual bricks in the system. This is because of Newton's third law of motion, which states that for every action, there is an equal and opposite reaction. Therefore, the force exerted by one brick on another is always equal in magnitude and opposite in direction to the force exerted by the second brick on the first.
Learn more about free-body diagram:
https://brainly.com/question/14626208
#SPJ11
what is the energy released (in mev) when three alpha particles combine to form 12c?
The energy released when three alpha particles combine to form 12C is 7.68 MeV. The process of three alpha particles combining to form 12C is known as alpha-particle triple fusion, which is the primary nuclear fusion process that occurs in stars.
The reaction can be written as: 3He → 12C + energy
where He represents an alpha particle (⁴₂He).
To calculate the energy released in the reaction, we need to use the mass-energy equivalence principle, which states that mass and energy are interchangeable. The energy released in the reaction is equal to the difference in the mass of the reactants and the mass of the product, multiplied by the speed of light squared (c²).
The mass of three alpha particles is: 3 x 4.00260 u/c² = 12.0078 u/c²
The mass of 12C is: 12.00000 u/c²
The difference in mass is: 12.0078 u/c² - 12.0000 u/c² = 0.0078 u/c²
Multiplying the difference in mass by the speed of light squared, we get: 0.0078 u/c² x (2.998 x 10⁸ m/s)² = 7.68 MeV
Therefore, the energy released when three alpha particles combine to form 12C is 7.68 MeV.
learn more about nuclear fusion here:
https://brainly.com/question/14019172
#SPJ11
what does the very small value of k_w indicate about the autoionization of water?
Answer:The very small value of K_w, which is the ion product constant of water, indicates that the autoionization of water is a relatively weak process. This means that at any given moment, only a small fraction of water molecules in a sample will be ionized into H+ and OH- ions.
At room temperature, for example, the value of K_w is approximately 1.0 x 10^-14, which means that the concentration of H+ ions and OH- ions in pure water is also very small (10^-7 M).
The weak autoionization of water is due to the relatively strong covalent bond between the oxygen and hydrogen atoms in a water molecule. Only a small percentage of water molecules are able to ionize due to the small amount of energy needed to break this bond.
This small ionization is enough, however, to give water some unique chemical properties, such as its ability to act as a solvent for many types of polar and ionic compounds.
In summary, the very small value of K_w indicates that the autoionization of water is a weak process due to the strong covalent bond between its hydrogen and oxygen atoms.
learn more about autoionization of water
https://brainly.com/question/27548797?referrer=searchResults
#SPJ11
a volume of 100 ml of 1.00 m hcl solution is titrated with 1.00 m naoh solution. you added the following quantities of 1.00 m naoh to the reaction flask. classify the following conditions based on whether they are before the equivalence point, at the equivalence point, or after the equivalence point.
a) 50 ml of NaOH solution b) 100 ml of NaOH solution c) 150 ml of NaOH solution d) 200 ml of NaOH solution a) Before the equivalence point b) At the equivalence point c) After the equivalence point d) After the equivalence point
In this titration, the HCl solution is the analyte and NaOH solution is the titrant. At the equivalence point, the moles of HCl and NaOH react in a 1:1 ratio, meaning all the HCl has reacted with the NaOH added. Before the equivalence point, there is excess HCl, and after the equivalence point, there is excess NaOH. a) 50 ml of NaOH solution: At this point, not all of the HCl has reacted with the NaOH, and there is still HCl left in the solution. Therefore, this is before the equivalence point.
b) 100 ml of NaOH solution: This is the point where the moles of HCl and NaOH react in a 1:1 ratio, which is the equivalence point.
c) 150 ml of NaOH solution: At this point, all the HCl has reacted with the NaOH, and there is excess NaOH in the solution. Therefore, this is after the equivalence point.
d) 200 ml of NaOH solution: This is also after the equivalence point since all the HCl has already reacted with the NaOH, and there is excess NaOH in the solution.
learn more about solution here:
https://brainly.com/question/30620786
#SPJ11
Consider two copper wires of equal length. One has twice the diameter of the other. How do the resistances of these two wires compare? A. Both wires have the same resistance. B. The thinner wire has four times the resistance of the thicker wire. C. The thinner wire has half the resistance of the thicker wire. D. The resistances of these wires cannot be compared.
The resistances of the two copper wires can be compared using the formula R = ρ(L/A), where R is the resistance, ρ is the resistivity, L is the length, and A is the cross-sectional area. Since both wires have the same length and are made of copper, their lengths and resistivities are the same.
The cross-sectional area of a wire is proportional to the square of its diameter. Therefore, if one wire has twice the diameter of the other, it will have four times the cross-sectional area. This means that the thinner wire has a higher resistance than the thicker wire, because the thinner wire has less space for electrons to flow through.
Using the formula for resistance, we can see that the thinner wire will have four times the resistance of the thicker wire. Therefore, the answer is B: the thinner wire has four times the resistance of the thicker wire.
For the cross-sectional area, A = π(D/2)^2, where D is the diameter. The thicker wire has twice the diameter of the thinner wire, so the cross-sectional area of the thicker wire is (π(2D/2)^2) = 4π(D/2)^2.
Comparing the resistances: R1 = ρ(L/A1) for the thinner wire and R2 = ρ(L/A2) for the thicker wire. Dividing R1 by R2:
R1/R2 = (ρ(L/A1))/(ρ(L/A2)) = A2/A1 = (4π(D/2)^2)/(π(D/2)^2) = 4.
So, the thinner wire has four times the resistance of the thicker wire. The correct answer is B.
To know more about resistances visit:-
https://brainly.com/question/30799966
#SPJ11
what happens to the wavelngth of two equal waves overlapping
When two equal waves overlap, they undergo a process called interference, which can result in constructive or destructive interference.
Constructive interference occurs when the crests and troughs of the two waves align, resulting in a wave with greater amplitude. Destructive interference occurs when the crest of one wave aligns with the trough of the other, leading to a wave with reduced amplitude or cancellation.
In both constructive and destructive interference, the wavelength of the resulting wave remains the same as the original waves, as wavelength depends on the properties of the medium and the source of the wave, not on the interference. However, the amplitude and intensity of the wave will change depending on the type of interference that occurs.
To know more about interference visit:-
https://brainly.com/question/22320785
#SPJ11
A quarter - wave lossless 100 Ohm line is terminated by a load ZL = 210 Ohm. If the voltage at the receiving and is 80 V, what is the voltage at the sending end?
A quarter-wave lossless 100 Ohm line is terminated by a load impedance ZL = 210 Ohm. If the voltage at the receiving end is 80 V, then the voltage at the sending end is 160 V.
A quarter-wave lossless transmission line has a characteristic impedance equal to the load impedance. Therefore, the characteristic impedance of the transmission line is 100 Ω, and the load impedance is 210 Ω.
When a wave travels along the line and reaches the load, it reflects back with the opposite polarity. At a distance of one-quarter wavelength from the load, the reflected wave is in phase with the incident wave, resulting in constructive interference.
Since the transmission line is lossless, the voltage and current amplitudes are constant along its length. Using the voltage reflection coefficient formula, we can calculate the voltage reflection coefficient Γ:
Γ = (ZL - Z0) / (ZL + Z0)
where Z0 is the characteristic impedance of the transmission line.
Plugging in the values, we get:
Γ = (210 - 100) / (210 + 100) = 0.375
The voltage at the receiving end is given as 80 V. Let's call the voltage at the sending end V. Using the voltage transmission coefficient formula, we can calculate the voltage at the sending end:
V = Vr (1 + Γ) / (1 - Γ)
where Vr is the voltage at the receiving end. Plugging in the values, we get:
V = 80 (1 + 0.375) / (1 - 0.375) = 160 V
Therefore, the voltage at the sending end is 160 V.
To know more about load impedance refer here:
https://brainly.com/question/31631145#
#SPJ11
a rod of negligible mass is pivoted at a point that is off-center, so that length l1 is different from length l2. the figures show two cases in which masses are suspended from the ends of the rod. in each case the unknown mass m is balanced so that the rod remains horizontal.
A mass is suspended from each end of a rod of unequal lengths. The rod is balanced horizontally by adjusting an unknown mass. Two cases are shown.
When a mass is suspended from each end of a rod of unequal lengths, the rod will not remain horizontal unless an unknown mass is suspended at a specific point on the rod. This point can be determined by balancing the rod horizontally. The position of the unknown mass can be calculated using the principle of moments, which states that the sum of the moments acting on an object must be equal to zero for it to be in equilibrium. In this case, the moments due to the masses on each end of the rod and the unknown mass must be equal and opposite. The position of the unknown mass can then be calculated using the formula m = (l1/l2) * M, where m is the unknown mass, l1 and l2 are the lengths of the rod on either side of the pivot point, and M is the mass on one end of the rod.
learn more about mass here:
https://brainly.com/question/18064917
#SPJ11
(a) Calculate the velocity (in m/s) of an electron that has a wavelength of 3.31 um. m/s
(b) Through what voltage (in V) must the electron be accelerated to have this velocity? (Assume the electron starts at rest.)
(a) The velocity of the electron that has a wavelength of 3.31 m/s is approximately 1.99 x 10^6 m/s.
(b) The voltage through which the electron must be accelerated to have this velocity is approximately 15.9 V.
(a) The de Broglie wavelength (λ) of an electron is related to its momentum (p) and mass (m) by the equation:
λ = h / p = h / (mv)
where h is Planck's constant, m is the mass of the electron, and v is its velocity.
Solving for v, we get:
v = h / (mλ)
Substituting the values given in the problem, we get:
v = (6.626 x 10^-34 J s) / [(9.109 x 10^-31 kg)(3.31 x 10^-6 m)] ≈ 1.99 x 10^6 m/s
Therefore, the velocity of the electron is approximately 1.99 x 10^6 m/s.
(b) To calculate the voltage required to accelerate the electron to the velocity calculated in part (a), we can use the formula for the kinetic energy of a particle:
KE = 1/2 mv^2
At the instant the electron exits the accelerating voltage, it has a kinetic energy equal to the potential energy gained from the voltage. Thus, we can set the kinetic energy equal to the potential energy and solve for the voltage:
KE = eV = 1/2 mv^2
Solving for V, we get:
V = KE / e = (1/2)mv^2 / e
Substituting the values given in the problem, we get:
V = (1/2)(9.109 x 10^-31 kg)(1.99 x 10^6 m/s)^2 / (1.602 x 10^-19 C) ≈ 15.9 V
Therefore, the voltage required to accelerate the electron to the given velocity is approximately 15.9 V.
For more such questions on de Broglie wavelength, click on:
https://brainly.com/question/30404168
#SPJ11
To calculate the velocity of an electron with a wavelength of 3.31 um, we can use the de Broglie equation: wavelength = h/momentum. where h is Planck's constant and momentum is mass times velocity.
Since we are dealing with an electron, we know the mass is 9.11 x [tex]10^{-31}[/tex] kg. Rearranging the equation to solve for velocity, we get velocity = momentum/mass = h/(mass*wavelength). Plugging in the values, we get: velocity = (6.626 x [tex]10^{-34}[/tex] J*s)/(9.11 x [tex]10^{-31}[/tex] kg * 3.31 x [tex]10^{-6}[/tex] m) = 2.20 x [tex]10^{6}[/tex] m/s. So the velocity of the electron is 2.20 x [tex]10^{6}[/tex] m/s. To find the voltage needed to accelerate the electron to this velocity, we can use the kinetic energy equation: KE = 0.5 * mass * [tex]velocity^{2}[/tex] = q * V. where KE is the kinetic energy of the electron, q is its charge, and V is the voltage. Since the electron starts at rest, its initial kinetic energy is zero. Rearranging the equation to solve for V, we get V = KE/q = (0.5 * mass * [tex]velocity^{2}[/tex])/q. Plugging in the values, we get: V = (0.5 * 9.11 x [tex]10^{-31}[/tex] kg * (2.20 x [tex]10^{6}[/tex] m/s)^2)/(1.6 x [tex]10^{-19}[/tex] C) = 106 V. So the electron needs to be accelerated through a voltage of 106 V to achieve a velocity of 2.20 x [tex]10^{6}[/tex] m/s.
Learn more about velocity here :
https://brainly.com/question/17127206
#SPJ11
how many different binary strings of length 6 exist?
There are 64 different binary strings of length 6 that exist.
A binary string is a sequence of characters that consists of only two characters, 0 and 1. In this case, you're interested in binary strings of length 6. To find out how many different binary strings of length 6 exist, we can use the concept of combinatorics.
For each position in the 6-character string, there are 2 possible choices - either 0 or 1. Since there are 6 positions, we can calculate the total number of different binary strings by multiplying the number of choices for each position together. This is because each choice for the first position can be combined with each choice for the second position, and so on.
Using the multiplication principle, we find the total number of different binary strings of length 6 as follows:
2 (choices for position 1) × 2 (choices for position 2) × 2 (choices for position 3) × 2 (choices for position 4) × 2 (choices for position 5) × 2 (choices for position 6)
This simplifies to:
2⁶ = 64
Therefore, there are 64 different binary strings of length 6.
Learn more about binary string here: https://brainly.com/question/29752361
#SPJ11
calculate the energy released in the fusion reaction 21h 21h→32he 10n . the atomic mass of 21h (deuterium) is 2.014101 u . express your answer in megaelectronvolts to three significant figures.
The energy released in the fusion reaction 21H + 21H → 32He + 10n is approximately 17.59 megaelectronvolts (MeV).
To calculate the energy released, we need to determine the mass difference before and after the reaction and convert it to energy using Einstein's mass-energy equivalence equation, E = mc².
The atomic mass of 21H (deuterium) is 2.014101 u, and the atomic mass of 32He is 4.002603 u. The neutron has a mass of approximately 1.008665 u.
The initial mass is (2 × 2.014101) u = 4.028202 u, and the final mass is (4.002603 + 1.008665) u = 5.011268 u.
The mass difference is Δm = (initial mass) - (final mass) = 4.028202 u - 5.011268 u = -0.983066 u.
Using the conversion factor 1 u = 931.5 MeV/c², we can calculate the energy released: ΔE = (-0.983066 u) × (931.5 MeV/c²) = -915.74 MeV.
Since energy is always released in nuclear reactions, we take the absolute value: |ΔE| = 915.74 MeV ≈ 17.59 MeV (to three significant figures).
learn more about energy here:
https://brainly.com/question/1932868
#SPJ11
true/false. The velocity with which an object is thrown upward from ground level is equal to the velocity with which it strikes the ground.
The statement that the velocity with which an object is thrown upward from ground level is equal to the velocity with which it strikes the ground is false.
The velocity with which an object is thrown upward from ground level is not equal to the velocity with which it strikes the ground. When an object is thrown upward, it experiences a constant acceleration due to gravity, causing it to slow down until it reaches its maximum height, at which point its velocity becomes zero. On its way back down, the object gains velocity due to the acceleration of gravity, and when it strikes the ground, its velocity is equal to the velocity it had when it was thrown upward, but in the opposite direction. This means that the velocity with which it strikes the ground is actually greater than the velocity with which it was thrown upward.
To know more about the velocity, click here;
https://brainly.com/question/17127206
#SPJ11
the fuel tank of a truck has a capacity of 55 gal. if the tank is full of gasoline 1sg = 0.7512, what is the mass and weight of the gasoline in si units?
The mass of the gasoline in the truck's fuel tank is approximately 156.359 kg, and the weight is approximately 1533.8 N in SI units.
To calculate the mass and weight of the gasoline in the truck's fuel tank, we will use the given capacity (55 gallons) and the specific gravity (1sg = 0.7512). First, we need to convert gallons to liters, and then we can find the mass using the specific gravity.
Finally, we'll calculate the weight using the mass and gravity.
1. Convert gallons to liters:
1 gallon ≈ 3.78541 liters
55 gallons ≈ 55 * 3.78541 ≈ 208.197 liters
2. Find the mass using specific gravity:
Specific gravity (sg) = mass of gasoline (kg) / mass of water (kg)
0.7512 = mass of gasoline / mass of water
Water has a density of 1 kg/L, so mass of water = 208.197 kg (since the volume of gasoline is 208.197 liters)
Mass of gasoline = 0.7512 * mass of water = 0.7512 * 208.197 ≈ 156.359 kg
3. Calculate the weight using mass and gravity:
Weight = mass * acceleration due to gravity
Weight = 156.359 kg * 9.81 m/s² ≈ 1533.8 N (Newtons)
So, the mass of the gasoline in the truck's fuel tank is approximately 156.359 kg, and the weight is approximately 1533.8 N in SI units.
To learn more about density, refer below:
https://brainly.com/question/29775886
#SPJ11
The outside mirror on the passenger side of a car is convex and hasa focal length of -5.5 m. Relative tothis mirror, a truck traveling in the rear has an object distanceof 6 m.
(a) Find the image distance of the truck.
1
m
(b) Find the magnification of the mirror.
2
When a lens is focussed at infinity, its focal length is calculated. The focal length of a lens indicates the angle of view (how much of the scene will be caught) and magnification.
(a) Using the mirror equation:
1/f = 1/do + 1/di
where f is the focal length, do is the object distance, and di is the image distance. Plugging in the given values:
1/-5.5 = 1/6 + 1/di
Solving for di:
di = -3.3 m
The image distance of the truck is -3.3 m, which means it is behind the mirror and virtual.
(b) Using the magnification equation:
m = -di/do
Plugging in the values:
m = -(-3.3)/6
m = 0.55
The magnification of the mirror is 0.55, which means the image of the truck is smaller than the actual truck.
So, the image distance of the truck is -3.3 m, and the magnification of the mirror is 0.55.
To know about Focal length visit:
https://brainly.com/question/29870264
#SPJ11
what is the entropy, in units of the boltzmann constant, of macrostate a1?
The entropy of macrostate a1 is approximately 1.39 times the Boltzmann constant. Entropy is a measure of the number of possible arrangements or configurations that a system can have while still maintaining the same macrostate.
It is defined as S = k ln(W), where S is the entropy, k is the Boltzmann constant, and W is the number of microstates that correspond to a given macrostate. In this case, we are given the macrostate a1, but we need to determine the number of microstates that correspond to it. Without more information, we can assume that each particle has two possible energy levels (e.g. spin up or spin down), so the total number of microstates is 2^(N), where N is the number of particles.
Plugging in the values, we get S = k ln(1) = 0, which means there is no entropy for this macrostate. However, this seems counterintuitive, since we know that there are multiple ways that the particles could be arranged (e.g. particle 1 in the first slot, particle 2 in the second slot, etc.). The reason for this discrepancy is that we have assumed that all the particles are indistinguishable, which is not strictly true. If we take into account the fact that the particles have different positions and momenta, then we would have to consider all the possible arrangements of the particles within the lowest energy level, which would increase the number of microstates and the entropy.
To know more about Entropy visit:
https://brainly.com/question/17278266
#SPJ11
150.0 g of he is contained in a 1.00 l balloon. when the balloon pops, the gas expands to fill a 7.50 l box. what is δssys for the process?
The value of δssys cannot be determined without additional information.
The question provides information about the amount of helium gas and the initial and final volumes of the system. However, in order to determine the value of δssys (the change in entropy of the system), we would also need to know the temperature and the pressure of the system at each step.
Without this additional information, it is not possible to calculate the value of δssys.
Learn more about calculate here:
https://brainly.com/question/30151794
#SPJ11
PLEASE HELP!!!
Photons with an energy of 5 electron volts strike a photoemissive surface causing the emission of 2 electron-volt photoelectrons. If photons with 10 electron volts of energy strike the same photoemissive surface, what will be the energy of the emitted photoelectrons?
Answer:
Easy.The energy of the emitted photoelectrons can be determined using the concept of the photoelectric effect. According to the photoelectric effect, the energy of the emitted photoelectrons is equal to the difference between the energy of the incident photons and the work function of the material.
In this case, we are given that the incident photons have an energy of 10 electron volts (eV). Let's assume the work function of the material is represented by W (in eV).
The energy of the emitted photoelectrons (Ee) can be calculated as:
Ee = incident photon energy - work function
Ee = 10 eV - W
We are also given that when photons with an energy of 5 eV strike the same surface, the emitted photoelectrons have an energy of 2 eV. Using this information, we can set up another equation:
2 eV = 5 eV - W
Solving this equation for W, the work function:
W = 5 eV - 2 eV
W = 3 eV
Now, we can substitute the value of the work function into the equation for the energy of the emitted photoelectrons:
Ee = 10 eV - W
Ee = 10 eV - 3 eV
Ee = 7 eV
Therefore, when photons with 10 electron volts of energy strike the photoemissive surface, the energy of the emitted photoelectrons will be 7 electron volts.
consider a 940-kg car initially moving at 31.5 m/s.
Given the mass of the car, which is 940 kg, and its initial velocity, which is 31.5 m/s, we can calculate its kinetic energy using the formula KE = 0.5 * m * v^2, where KE is the kinetic energy, m is the mass, and v is the velocity. Therefore, the kinetic energy of the car is KE = 0.5 * 940 kg * (31.5 m/s)^2 = 467,190 J.
Now, let's assume that the car is moving on a flat road with no friction or air resistance. If there are no external forces acting on the car, it will continue to move at a constant velocity, also known as the law of inertia.
However, if an external force is applied to the car, such as a braking force, it will start to decelerate and eventually come to a stop. The amount of deceleration depends on the magnitude of the force and the mass of the car, as given by the equation F = m * a, where F is the force, m is the mass, and a is the acceleration.
To answer the question more than 100 words, we can also consider the implications of the car's mass and velocity in terms of its safety and energy efficiency. A car with a higher mass will require more force to stop or change its direction, which can make it more dangerous in collisions. On the other hand, a car with a higher velocity will consume more fuel and produce more emissions, which can contribute to environmental pollution and climate change. Therefore, it is important to balance these factors when designing and using cars for transportation.
To know more about mass visit:
https://brainly.com/question/19694949
#SPJ11
decide the outcome of the hypothetical situation by dragging the label into the appropriate category.
In order to decide the outcome of a hypothetical situation, it is important to carefully consider all relevant factors and then determine the appropriate course of action.
This may involve analyzing the various options available, considering potential consequences, and assessing the likelihood of different outcomes. Once you have carefully considered all of these factors, you can then label the situation and drag it into the appropriate category based on the most likely outcome. This process requires careful analysis and critical thinking skills, as well as the ability to make informed decisions based on available information.
Learn more about appropriate here:
https://brainly.com/question/9262338
#SPJ11
The Ideal efficiency for a heat engine operating between thetemperatures of 227 degrees C and 27 degrees C is what percent?
The ideal efficiency of the heat engine is 88.1%.
The ideal efficiency of a heat engine operating between two temperatures can be determined by using the Carnot cycle. The efficiency is given by the formula (Th - Tc)/Th, where Th is the temperature of the hot reservoir and Tc is the temperature of the cold reservoir.
In this case, Th = 227°C and Tc = 27°C. Therefore, the ideal efficiency of the heat engine can be calculated as (227 - 27)/227 = 0.881 or 88.1%. This means that the heat engine can convert 88.1% of the heat energy it receives into useful work. It is important to note that this is an ideal efficiency and real-world heat engines may have lower efficiencies due to factors such as friction, heat loss, and other inefficiencies in the system.
To know more about heat engine operating visit:
https://brainly.com/question/13144439
#SPJ11
What message does Kurt Vonnegut convey through the satire "Harrison Bergeron," and how do the characters develop this message?
Constructed Response (A. C. E. ): You should cite selections from the text to support your answer
In the satire "Harrison Bergeron," Kurt Vonnegut conveys a message about the dangers of extreme equality and the suppression of individuality. The characters in the story, particularly Harrison and the Bergeron family, highlight this message through their experiences and interactions.
In "Harrison Bergeron," Kurt Vonnegut uses satire to criticize the concept of absolute equality. The story is set in a dystopian society where the government enforces strict regulations to ensure everyone is equal in every aspect. The characters and their development play a crucial role in conveying the message.
The character of Harrison Bergeron himself becomes a symbol of individuality and rebellion against oppressive equality. Despite being burdened by physical handicaps imposed by the government, Harrison stands as a powerful figure who refuses to conform. His brief display of exceptional talent and strength before being subdued represents the innate desire for freedom and self-expression.
The Bergeron family, particularly George and Hazel, also contribute to the message. George, who has above-average intelligence, is forced to wear a mental handicap device that disrupts his thoughts. Through his struggles and dissatisfaction, Vonnegut demonstrates the detrimental effects of suppressing individual abilities and potential. Hazel, on the other hand, represents the passive acceptance of the system, showing the danger of complacency in the face of oppressive equality.
Overall, Vonnegut's "Harrison Bergeron" satirically warns against the dangers of excessive equality and the suppression of individuality, using characters like Harrison and the Bergeron family to illustrate the negative consequences and advocate for the preservation of personal freedom.
Learn more about suppression here:
https://brainly.com/question/12493533
#SPJ11
Which analogy best describes voltage?(1 point)
Responses
turbine or mill inserted into a flow of water
length of the pipe through which water moves
pressure of water moving through a pipe
diameter of a pipe through which water move
Need some help with this one, and the ''Electrical Energy Properties Quick Check'' if anybody is willing to give it.
The best analogy that describes voltage is "pressure of water moving through a pipe." Just like water pressure, voltage is a measure of the force that drives electric current through a circuit.
A string with both ends held fixed is vibrating in its third harmonic. The waves have a speed of 192m/s and a frequency of 215 Hz. The amplitude of the standing wave at an antinode is 0.450 cm.
(A)Calculate the amplitude at point on the string a distance of 22.0cm from the left-hand end of the string.
(B)How much time does it take the string to go from its largest upward displacement to its largest downward displacement at this point?
(C)Calculate the maximum transverse velocity of the string at this point.
(D)Calculate the maximum transverse acceleration of the string at this point.
pls show work
A).The amplitude (A) at the desired point:
A = (0.450 cm) sin((2π × 0.22 m) / (192 m/s / 215 Hz))
B). It takes approximately 0.0023255 seconds for the string to go from its largest upward displacement to its largest downward
displacement at the desired point.
C). The maximum transverse velocity at the desired point is v_max = 2π × 215 Hz × A.
D). The maximum transverse acceleration at the desired point is a_max = (2π × 215 Hz)² × A.
A) How to calculate the amplitude at a point on the string?We can use the formulas and principles related to standing waves on a string.
Given:
- Speed of the waves (v): 192 m/s
- Frequency of the waves (f): 215 Hz
- Amplitude at an antinode (A_antinode): 0.450 cm
- Distance from the left-hand end (x): 22.0 cm
We need to convert the amplitude and distance to meters for consistency in units.
To solve this problem, we can use the formulas and principles related to standing waves on a string.
Given:
- Speed of the waves (v): 192 m/s
- Frequency of the waves (f): 215 Hz
- Amplitude at an antinode (A_antinode): 0.450 cm
- Distance from the left-hand end (x): 22.0 cm
We need to convert the amplitude and distance to meters for consistency in units.
The amplitude at any point on a standing wave is given by:
A = A_antinode × sin((2πx) / λ)
Where:
A = Amplitude at the desired point
A_antinode = Amplitude at an antinode
x = Distance from the left-hand end of the string
λ = Wavelength of the wave
To find the wavelength (λ), we can use the formula:
v = f × λ
Rearranging the formula:
λ = v / f
Substituting the given values:
λ = 192 m/s / 215 Hz
Now we can calculate the amplitude (A) at the desired point:
A = (0.450 cm) sin((2π × 0.22 m) / (192 m/s / 215 Hz))
Calculating the expression will give us the amplitude at the desired point.
B) How to Calculate the time for the string to displacement?Calculating the time for the string to go from the largest upward displacement to the largest downward displacement:
The time period of a wave (T) is the reciprocal of the frequency:
T = 1 / f
The time it takes for the string to go from the largest upward displacement to the largest downward displacement at a given point is half of the time period (T/2).
To calculate the time:
T/2 = (1 / f) / 2
Substituting the given frequency:
T/2 = (1 / 215 Hz) / 2
T/2 = 0.004651 Hz / 2 ≈ 0.0023255 seconds
Therefore, it takes approximately 0.0023255 seconds for the string to go from its largest upward displacement to its largest downward
displacement at the desired point.
C) How to Calculate the maximum transverse velocity?Calculating the maximum transverse velocity of the string at the desired point:
The maximum transverse velocity (v_max) is given by:
v_max = 2πfA
Where:
v_max = Maximum transverse velocity
f = Frequency
A = Amplitude at the desired point
Substituting the given values:
v_max = 2π × 215 Hz × A
Calculating the expression will give us the maximum transverse velocity at the desired point.
D) How to calculate the maximum transverse acceleration?Calculating the maximum transverse acceleration of the string at the desired point:
The maximum transverse acceleration (a_max) is given by:
a_max = (2πf)² × A
Where:
a_max = Maximum transverse acceleration
f = Frequency
A = Amplitude at the desired point
Substituting the given values:
a_max = (2π × 215 Hz)² × A
Calculating the expression will give us the maximum transverse acceleration at the desired point.
Please note that the calculations may involve rounding off values, so the final answers may slightly differ depending on the level of precision used.
Learn more about waves.
brainly.com/question/29334933
#SPJ11
the mass of a cube of metal is 4.46 kg. what is the density if the cube measures 8 cm on each side?
The density of the cube measuring 8 cm on each side and 4.46 kg is approximately 8.71 g/cm³.
To find the density of the metal cube, you'll need to use the formula for density, which is:
Density = Mass / Volume
Given that the mass of the cube is 4.46 kg and each side measures 8 cm, you first need to find the volume of the cube. The formula for the volume of a cube is:
Volume = Side³
So, the volume of this cube is 8 cm × 8 cm × 8 cm = 512 cubic centimeters.
Now, to find the density, divide the mass by the volume:
Density = 4.46 kg / 512 cm³
Since we need the density in kg/cm³, we'll convert the mass to grams by multiplying by 1000:
Density = (4.46 kg × 1000 g/kg) / 512 cm³ = 4460 g / 512 cm³ ≈ 8.71 g/cm³
The density of the metal cube is approximately 8.71 g/cm³.
Learn more about density here: https://brainly.com/question/26364788
#SPJ11
(a) What is the rate of heat conduction through the 3.00-cm-thick fur of a large animal having a 1.40-m2 surface area? Assume that the animal’s skin temperature is 32.0ºC , that the air temperature is −5.00ºC , and that fur has the same thermal conductivity as air. (b) What food intake will the animal need in one day to replace this heat transfer?
(a) The rate of heat conduction through the fur is 16,800 W.
(b)The animal needs to consume approximately 8.72 x 10^9 calories of food
(a)The rate of heat conduction through the fur can be found using the formula:
Q/Δt = kA(ΔT/d)
where Q/Δt is the rate of heat conduction, k is the thermal conductivity of the fur (assumed to be the same as air), A is the surface area, ΔT is the temperature difference between the skin and air, and d is the thickness of the fur.
Substituting the given values:
Q/Δt = (0.024 W/m·K)(1.40 m^2)(32.0°C - (-5.00°C))/(0.03 m)
Q/Δt = 16,800 W
(b)To replace the heat transfer through the fur in one day, the animal must consume an amount of food that provides the same amount of energy. The energy needed can be found using the formula:
Energy = power x time
where power is the rate of heat conduction found in part (a) and time is the number of seconds in one day:
Energy = (16,800 W)(24 hours)(60 min/hour)(60 s/min)
Energy = 3.65 x 10^10 J
Converting to food energy, 1 calorie (cal) = 4.184 J, so:
Food energy = (3.65 x 10^10 J)/(4.184 J/cal)
Food energy = 8.72 x 10^9 cal
To know more about rate of heat conduction refer here
https://brainly.com/question/20815787#
#SPJ11
a particular person's pupil is 5.0 mm in diameter, and the person's normal‑sighted eye is most sensitive at a wavelength of 558 nm. what is angular resolution r of the person's eye, in radians?
The angular resolution of the person's eye is approximately 1.362 *[tex]10^{-4[/tex]radians.
The angular resolution of an eye is determined by the smallest angle that the eye can resolve between two distinct points. This angle is given by the formula:
r = 1.22 * λ / D
where λ is the wavelength of light and D is the diameter of the pupil.
Substituting the given values, we get:
r = 1.22 * 558 nm / 5.0 mm
Note that we need to convert the diameter of the pupil from millimeters to meters to ensure that the units match. 5.0 mm is equal to 0.005 m.
r = 1.22 * 558 * [tex]10^{-9[/tex] m / 0.005 m
r = 1.362 * [tex]10^{-4[/tex]radians
Therefore, the angular resolution of the person's eye is approximately 1.362 * [tex]10^{-4[/tex] radians.
Learn more about angular resolution here:
https://brainly.com/question/31858807
#SPJ11
Hi, please I need help on how to solve these problems. Thank you!
Problem 1)
Mass of hydrogen requirement of a fuel cell in running a 250 A current gadget for 30 min is [Molar mass of hydrogen=2.01; n=2.0 and F=96500]
Problem 2)
What number of stacked cells is needed for generation of 6.00 kW of power at the average voltage of the fuel cell 0.60 V and current 100A?
The mass of hydrogen required by the fuel cell to run the gadget for 30 min is 2.78 grams.10 stacked cells are needed to generate 6.00 kW of power at the average voltage of the fuel cell of 0.60 V and current of 100 A.
Problem 1:
The mass of hydrogen required by a fuel cell can be calculated using the following formula:
mass = (I * t * n * M) / (2 * F)
Given:
I = 250 A (current)
t = 30 min = 1800 s (time)
n = 2 (number of electrons transferred per mole of hydrogen)
M = 2.01 g/mol (molar mass of hydrogen)
F = 96500 C/mol (Faraday constant)
Substituting these values into the formula, we get:
mass = (250 A * 1800 s * 2 * 2.01 g/mol) / (2 * 96500 C/mol)
mass = 2.78 g
Therefore, the mass of hydrogen required by the fuel cell to run the gadget for 30 min is 2.78 grams.
Problem 2:
The power generated by a fuel cell can be calculated using the following formula:
P = V * I
where P is the power (in watts), V is the voltage (in volts), and I is the current (in amperes).
Given:
P = 6.00 kW (power)
V = 0.60 V (voltage)
I = 100 A (current)
Substituting these values into the formula, we get:
P = V * I
6000 W = 0.60 V * 100 A
Solving for V, we get:
V = P / I
V = 6000 W / 100 A
V = 60 V
Therefore, the average voltage of the fuel cell is 60 V.
The number of stacked cells needed can be calculated using the following formula:
n = P / (V * I)
where n is the number of stacked cells, P is the power (in watts), V is the average voltage of the fuel cell (in volts), and I is the current (in amperes).
Substituting the given values, we get:
n = 6.00 kW / (60 V * 100 A)
n = 10
Therefore, 10 stacked cells are needed to generate 6.00 kW of power at the average voltage of the fuel cell of 0.60 V and current of 100 A.
Learn more about voltage here:
https://brainly.com/question/29445057
#SPJ11
What is the frequency of light emitted from a hydrogen atom that makes a transition from the the n = 4 state to the n = 2 state (in Hz)?A hydrogen atom initially staying in the n = 7 state with energy Ei undergoes a transition to the ground state with energy Ef. What is the energy difference Ef – Ei (in eV; answer sign and magnitude)?What is the wavelength of light that can excite a hydrogen atom from the n = 2 state to the n = 6 state (in m)?
A hydrogen atom can be excited from the n = 2 state to the n = 6 state with a wavelength of around 3.65 x 10⁻¹⁵ m.
To calculate the frequency of light emitted from a hydrogen atom during a transition, we can use the Rydberg formula:
[tex]\frac{1}{\lambda} = R_H \left( \frac{1}{n_f^2} - \frac{1}{n_i^2} \right)[/tex]
where λ is the wavelength, R_H is the Rydberg constant for hydrogen (approximately 3.29 x 10¹⁵ Hz), [tex]n_f[/tex] is the final state, and [tex]n_i[/tex] is the initial state.
For the transition from n = 4 to n = 2, we have:
[tex]\frac{1}{\lambda} = 3.29 \times 10^{15} \, \text{Hz} \times \left(\frac{1}{2^2} - \frac{1}{4^2}\right)[/tex]
[tex]\frac{1}{\lambda} = 3.29 \times 10^{15} \, \text{Hz} \times \left(\frac{1}{4} - \frac{1}{16}\right)[/tex]
[tex]\frac{1}{\lambda} = 3.29 \times 10^{15} \, \text{Hz} \times \frac{3}{16}[/tex]
[tex]\frac{1}{\lambda}[/tex] = 1.21 x 10¹⁵ Hz
So, the frequency of light emitted during this transition is approximately 1.21 x 10¹⁵ Hz.
To calculate the energy difference [tex]Ef - Ei[/tex], we can use the formula:
ΔE = [tex]E_i[/tex] - [tex]E_f[/tex]
where ΔE is the energy difference, [tex]E_i[/tex] is the initial energy, and [tex]E_f[/tex] is the final energy.
The energy of a hydrogen atom in a given state can be calculated using the formula:
[tex]E = \frac{-13.6 \, \text{eV}}{n^2}[/tex]
For the transition from n = 7 to the ground state (n = 1), we have:
[tex]ΔE = \left(-\frac{13.6 \text{ eV}}{1^2}\right) - \left(-\frac{13.6 \text{ eV}}{7^2}\right)[/tex]
= -13.6 eV + 0.271 eV
= -13.329 eV
So, the energy difference [tex]Ef - Ei[/tex] is approximately -13.329 eV.
To calculate the wavelength of light that can excite a hydrogen atom from the n = 2 state to the n = 6 state, we can use the Rydberg formula as mentioned earlier:
[tex]\frac{1}{\lambda} = R_H \left( \frac{1}{n_f^2} - \frac{1}{n_i^2} \right)[/tex]
For this transition, we have:
[tex]\frac{1}{\lambda} = 3.29 \times 10^{15} \text{ Hz} \left( \frac{1}{6^2} - \frac{1}{2^2} \right)[/tex]
[tex]\frac{1}{\lambda} = 3.29 \times 10^{15} \text{ Hz} \left( \frac{1}{36} - \frac{1}{4} \right)[/tex]
[tex]\frac{1}{\lambda} = 3.29 \times 10^{15} \text{ Hz} \left( \frac{3}{36} \right)[/tex]
[tex]\frac{1}{\lambda}[/tex]= 2.74 x 10¹⁴ Hz
Now, we can calculate the wavelength:
[tex]\lambda = \frac{1}{2.74 \times 10^{14} \text{ Hz}}[/tex]
= 3.65 x 10⁻¹⁵ m
So, the wavelength of light that can excite a hydrogen atom from the n = 2 state to the n = 6 state is approximately 3.65 x 10⁻¹⁵ m.
To know more about the wavelength of light refer here :
https://brainly.com/question/20462619#
#SPJ11