the pendulum illustrated above has a length of 2 m and a bob of mass 0.04 kg. it is held at an angle ѳ, as shown, where cosѳ = 0.9. the frequency of oscillation is most nearly

The mass of the sample of 238/92U is 0.401 kg.

First, we can use the decay constant (λ) formula to calculate the decay rate:

[tex]λ = ln(2)/t1/2 = ln(2)/(4.468×10^9 yr) ≈ 1.549 × 10^-10 /s[/tex]

Then, we can use the decay rate formula to find the number of atoms (N) in the sample:

[tex]N = (decay rate) / λ = 450 / (1.549 × 10^-10 /s) ≈ 2.906 × 10^12 atoms[/tex]

Finally, we can use the atomic mass of 238/92U (which is approximately 238 g/mol) to calculate the mass of the sample:

mass = N × (atomic mass) = 2.906 × 10^12 atoms × (238 g/mol / 6.022 × 10^23 atoms/mol) ≈ 0.401 kg

Therefore, the mass of the sample is 0.401 kg (to three significant figures).

Learn more about  significant here:

https://brainly.com/question/31037173

#SPJ11

The electric potential at the origin of the xy-coordinate system due to two positive point charges, both of magnitude 4.0x10^6C, situated along the x-axis at x=-2.0m and x=2.0m is 0.

To calculate the electric potential at the origin, we first need to find the electric potential due to each charge separately. Using the formula for electric potential due to a point charge V=kQ/r, where k is Coulomb's constant, Q is the magnitude of the charge, and r is the distance from the charge to the point where the potential is being calculated, we can calculate the electric potential due to each charge as follows:

V1=k(4.0x10^6)/2.0=2.16x10^7V
V2=k(4.0x10^6)/2.0=2.16x10^7V

Since the charges are of the same magnitude and opposite signs, their electric potentials cancel out at the origin, resulting in a net electric potential of 0. Therefore, the correct answer is 0.

To know more about electric potential, click here;

https://brainly.com/question/12645463

#SPJ11

You would absorb 8.5 ×[tex]10^{6}[/tex]J of solar energy in a 60-minute sunbath.

The amount of solar energy you absorb in a 60-minute sunbath can be estimated as follows:

Calculate the area of the beach blanket you occupy:

Area = length x width = (1.7 m) x (0.3 m) = 0.51 [tex]m^{2}[/tex]

Calculate the fraction of solar energy that reaches the surface of the Earth:

Fraction reaching Earth's surface = 60% = 0.6

Calculate the fraction of solar energy that you absorb:

Fraction absorbed = 50% = 0.5

Calculate the solar energy that you absorb per unit area:

Energy absorbed per unit area = (intensity of solar radiation at the top of Earth's atmosphere) x (fraction reaching Earth's surface) x (fraction absorbed)

Energy absorbed per unit area = (1,370 W/[tex]m^{2}[/tex]) x (0.6) x (0.5) = 411 W/[tex]m^{2}[/tex]

Calculate the solar energy you absorb in a 60-minute sunbath:

Energy absorbed = (energy absorbed per unit area) x (area of beach blanket) x (time)

Energy absorbed = (411 W/[tex]m^{2}[/tex]) x (0.51 [tex]m^{2}[/tex]) x (60 min x 60 s/min) = 8,466,120 J

Therefore, you would absorb approximately 8.5 ×[tex]10^{6}[/tex] J of solar energy in a 60-minute sunbath. Note that this is an order-of-magnitude estimate and the actual value may be different due to various factors such as the actual solar radiation intensity, the actual fraction of solar energy reaching Earth's surface, and the actual fraction of solar energy absorbed by your body, among others.

know more about solar energy here:

https://brainly.com/question/30134980

#SPJ11

An elementary particle travels 60 km through the atmosphere at a speed of 0.9996c. According to the particle, the thickness of the atmosphere is 32.4 km.

According to the particle, the length of the atmosphere it travels through is shortened due to time dilation and length contraction effects predicted by special relativity.

The proper length of the atmosphere (i.e., the length measured by a stationary observer on Earth) is L = 60 km.

The length contracted distance, as measured by the particle, is given by

L' = L / γ

Where γ is the Lorentz factor

γ = 1 / [tex]\sqrt{(1- v^{2} /c^{2} )[/tex]

Where v is the velocity of the particle and c is the speed of light.

Substituting the given values into the above equation, we get

γ = 1 / [tex]\sqrt{(1- (0.9996c)^{2} / c^{2} )[/tex]

γ = 1.854

Therefore, the length of the atmosphere as measured by the particle is

L' = L / γ

L' = 60 km / 1.854

L' ≈ 32.4 km

Therefore, according to the particle, the thickness of the atmosphere is 32.4 km.

To know more about thickness here

https://brainly.com/question/30764128

#SPJ4

The capacitance of the two wires is approximately 6.07 pF (pico-Farads).

To find the capacitance of the two wires, we'll use the formula for capacitance, which is:

Capacitance (C) = Charge (Q) / Potential Difference (V)

Given the information in your question, we have:

Charge (Q) = 85 pC (pico-Coulombs) = 85 x 10^(-12) C (Coulombs)
Potential Difference (V) = 14 V

Now we can calculate the capacitance:

C = (85 x 10^(-12) C) / (14 V)

C ≈ 6.07 x 10^(-12) F (Farads)

So, the capacitance of the two wires is approximately 6.07 pF (pico-Farads).

To learn more about wires, refer below:

https://brainly.com/question/12984460

#SPJ11

The acceleration of a shopping cart pushed with a 85 N force, considering its mass of 37 kg, can be calculated using Newton's second law of motion.

According to Newton's second law of motion, the acceleration of an object is directly proportional to the net force applied to it and inversely proportional to its mass. The formula for calculating acceleration is given by a = F/m, where "a" represents acceleration, "F" denotes the net force, and "m" represents the mass of the object.

In this case, the net force acting on the shopping cart is 85 N, and its mass is 37 kg. Plugging these values into the formula, we can calculate the acceleration as follows:

a = F/m

= 85 N / 37 kg

≈ 2.30 m/s²

Therefore, the acceleration of the shopping cart is approximately 2.30 m/s² when a force of 85 N is applied to it.

Learn more about Newton's laws of motion here:

https://brainly.com/question/974124

#SPJ11

The maximum safe speed to prevent slipping can be determined using the coefficient of static friction (μs = 0.5).

The coefficient of static friction (μs) represents the frictional force between two surfaces in contact when they are at rest relative to each other. To determine the maximum safe speed without slipping, we need to equate the frictional force (static friction) to the centripetal force.

The centripetal force is given by the equation Fc = m * v² / r, where m is the mass of the car, v is the velocity, and r is the radius of the curve. The frictional force (Fs) can be calculated as Fs = μs * m * g, where g is the acceleration due to gravity.

To prevent slipping, the maximum safe speed occurs when the frictional force is equal to the centripetal force. By equating Fs to Fc and rearranging the equation, we can solve for the maximum safe speed (v). Neglecting the size of the car, we can calculate the maximum safe speed using the given coefficient of static friction (μs = 0.5).

Learn more about  force

brainly.com/question/30507236

#SPJ11

The minimum frequency of light needed to release electrons from the metal is approximately 9.67 x [tex]10^1^4[/tex]Hz.

The minimum frequency of light required to cause electrons to be emitted from a metal can be found by using equation:

E = hf

where E is the energy of a single photon, h is Planck's constant (6.626 x [tex]10^-^3^4[/tex] J·s), and f is the frequency of light.

The work function, denoted by φ, is the minimum energy required to remove an electron from the metal. In this case, the work function is given as 4.00 eV.

We need to convert the work function from electron volts (eV) to joules (J) since Planck's constant is in joules. The conversion factor is 1 eV = 1.602 x [tex]10^-^1^9[/tex]J.

Therefore, the work function in joules is:

φ = 4.00 eV × (1.602 x [tex]10^-^1^9[/tex] J/eV) = 6.408 x[tex]10^-^1^9[/tex]J

We can equate the energy of a single photon to the work function

E = φ

hf = φ

From this equation, we can solve for the frequency f:

f = φ / h

Substituting the values:

f = (6.408 x [tex]10^-^1^9[/tex]J) / (6.626 x [tex]10^-^3^4[/tex]J·s)

f ≈ 9.67 x 1[tex]0^1^4[/tex]Hz

Therefore, the minimum frequency of light required to cause electrons to be emitted from the metal is approximately 9.67 x[tex]10^1^4[/tex] Hz.

Learn more about frequency

brainly.com/question/29739263

#SPJ11

The correct option is (a) 45.6"".

The critical angle for total internal reflection occurs when the angle of incidence of a light ray at the interface between two materials is equal to or greater than the critical angle. The critical angle can be calculated using the formula:

sin(critical angle) = 1/n

where n is the refractive index of the first material with respect to the second material.

In this case, the material has a refractive index of 1.40 with respect to air. Therefore, the critical angle can be calculated as:

sin(critical angle) = 1/1.40

critical angle = sin^-1(1/1.40) = 45.6 degrees

Click the below link, to learn more about Total internal reflection:

https://brainly.com/question/28231417

#SPJ11

The peak current is  1.14 A

The phase angle is 17.7 degrees

The power lost is  130 W

The capacitive reactance is;

Xc = 1/2πfc

Xc = 1/2 * 3.14 * 60 * 30 * 10^-6

Xc = 88.5 ohm

XL = 2πfL

= 2 * 3.14 *60 * 0.15

= 56.5 ohm

Impedance;

Z = √R^2 + (XL - XC)^2

Z = √(100)^2 + (56.5 - 88.5)^2

Z = 105 ohm

I = V/Z

= 120V/105 Ohm

= 1.14 A

The phase angle is;

Tan-1 (XL - XC)/R

= Tan-1 (-32/100)

= 17.7 degrees

The average power loss is;

IV cosφ

= 1.14 * 120 8 Cos 17.7

= 130 W

Learn more about RLC circuit:https://brainly.com/question/29898671

#SPJ4

(a) The motor has done 25.12 J of work on the rotor when it has rotated through four revolutions.

(b) The rotor's angular velocity is approximately 167.55 rpm when it has rotated through four revolutions.

To calculate the work done by the motor on the rotor, we use the formula W = τΔθ, where W is the work done, τ is the torque exerted by the motor, and Δθ is the angle through which the rotor has rotated. Since the rotor has rotated through four revolutions, Δθ = 8π radians. Thus, W = 0.8 N-m × 8π rad = 25.12 J.

To calculate the angular velocity of the rotor, we use the formula ω = Δθ/Δt, where ω is the angular velocity, Δθ is the angle through which the rotor has rotated, and Δt is the time taken to rotate through that angle. Since the rotor has rotated through four revolutions, Δθ = 8π radians. The time taken can be calculated from the formula Δθ = ωt. Rearranging this formula, we get t = Δθ/ω. Substituting the values, we get t = 8π/ω. We know that one revolution is equal to 2π radians, so four revolutions is equal to 8π radians. Therefore, t = 4/ω. Substituting this value of t in the formula for ω, we get ω = Δθ/t = (8π)/(4/ω) = 2ωπ. Solving for ω, we get approximately 167.55 rpm.

Learn more about values here:

https://brainly.com/question/30145972

#SPJ11

The period of the pendulum is approximately 4.55 seconds (1.45π seconds).

The period of a pendulum can be calculated using the formula T=2π√(L/g), where T is the period in seconds, L is the length of the pendulum in meters, and g is the acceleration due to gravity in m/s^2. In this case, the pendulum has a length of 5.15 m and the acceleration due to gravity is 9.8 m/s^2.

Using the formula, we can find the period of the pendulum as follows:

T=2π√(L/g)
T=2π√(5.15/9.8)
T=2π√0.525
T=2π(0.725)
T=1.45π

Consequently, the pendulum's period is roughly 4.56 seconds. The pendulum swings fully from one side to the other and back again in 4.56 seconds, according to this calculation. The period of a pendulum increases with its length and decreases with its length. Similar to how a period shortens with increasing gravity, it lengthens with decreasing gravity.

To know more about the pendulum, click here;

https://brainly.com/question/31967853

#SPJ11

Because angular momentum must be conserved, as a gas cloud contracts due to gravity, it will spin faster. The correct answer is (b)

This is due to the conservation of angular momentum, which states that the product of the angular velocity and the moment of inertia of an object must remain constant if there is no net external torque acting on it.

As the cloud contracts, its moment of inertia decreases, so in order to conserve angular momentum, the angular velocity (spin rate) of the cloud must increase.

This is similar to what happens when an ice skater pulls in their arms while spinning - they spin faster to conserve their angular momentum. Therefore, the correct answer is (b) spin faster.

For more question on angular momentum click on

https://brainly.com/question/4126751

#SPJ11

b. spin faster.

This is because as the gas cloud contracts due to gravity, its radius decreases, which means its moment of inertia decreases. In order for angular momentum to be conserved, the cloud must spin faster to compensate for the decrease in moment of inertia.

As a gas cloud contracts due to gravity, it needs to conserve angular momentum. To do this, the cloud will spin faster. This is because angular momentum (L) is given by the formula L = Iω, where I is the moment of inertia and ω is the angular velocity. As the cloud contracts, its moment of inertia (I) decreases, so to maintain constant angular momentum (L), the angular velocity (ω) must increase, causing the gas cloud to spin faster.

Learn more about gas cloud here : brainly.com/question/9080971

#SPJ11

a)The de Broglie wavelength of a 200g baseball moving at a speed of 30 m/s is approximately 1.104 × 10^(-34) meters.

To calculate the de Broglie wavelength of a baseball, we can use the following formula:

λ = h / p

where:

λ is the de Broglie wavelength,

h is the Planck's constant (approximately 6.62607015 × 10^(-34) m^2 kg / s),

p is the momentum of the baseball.

The momentum (p) can be calculated as the product of the mass (m) and the velocity (v):

p = m * v

Given that the mass (m) of the baseball is 200 grams, which is equal to 0.2 kilograms, and the speed (v) is 30 m/s, we can now calculate the de Broglie wavelength:

p = (0.2 kg) * (30 m/s) = 6 kg·m/s

λ = (6.62607015 × 10^(-34) m^2 kg / s) / (6 kg·m/s)

λ ≈ 1.104 × 10^(-34) meters

Therefore, the de Broglie wavelength of a 200g baseball moving at a speed of 30 m/s is approximately 1.104 × 10^(-34) meters.

b) The speed of a 200g baseball with a de Broglie wavelength of 0.20 nm is approximately 1.657 × 10^(-24) m/s.

To calculate the speed of the baseball with a given de Broglie wavelength, we can rearrange the formula:

p = h / λ

First, let's convert the given de Broglie wavelength of 0.20 nm to meters:

λ = 0.20 nm = 0.20 × 10^(-9) m

Now we can use the formula to calculate the momentum (p):

p = (6.62607015 × 10^(-34) m^2 kg / s) / (0.20 × 10^(-9) m)

p ≈ 3.313 × 10^(-25) kg·m/s

To find the speed (v), we divide the momentum (p) by the mass (m):

v = p / m

v = (3.313 × 10^(-25) kg·m/s) / (0.2 kg)

v ≈ 1.657 × 10^(-24) m/s

Therefore, the speed of a 200g baseball with a de Broglie wavelength of 0.20 nm is approximately 1.657 × 10^(-24) m/s.

To know more about de Broglie wavelength refer here

https://brainly.com/question/17295250#

#SPJ11

To be negotiable, this instrument must include on its face no conditions. The correct option is b.

In the context of negotiable instruments, such as promissory notes, there are certain requirements that must be met for the instrument to be legally negotiable. One of these requirements is that the instrument must be unconditional on its face. This means that the instrument must not contain any conditions or qualifications that would affect the holder's right to payment.

In the case of Milo's promissory note to National Lenders, the note promises to pay a specific sum of money with interest in installments, with the final payment due on a specific date. This is an unconditional promise to pay, and there are no conditions or qualifications that would affect National Lenders' right to payment. Therefore, the instrument meets the requirement of being unconditional on its face and is negotiable.

It is worth noting that there may be other conditions or qualifications related to the sale of the goods or the repayment of the loan that are not included on the face of the instrument. However, as long as these conditions do not affect the holder's right to payment, they do not affect the negotiability of the instrument.

Hence, b. is the correct option.

To know more about negotiable instruments, refer to the link below:

https://brainly.com/question/28326209#

#SPJ11

Explanation:

The change in an object's momentum is equal to the final momentum minus the initial momentum.

The momentum of an object is given by the product of its mass and velocity:

Initial momentum = mass * initial velocity

Final momentum = mass * final velocity

Given:

Mass of the tennis ball = 5.69x10^-2 kg

Initial velocity = 13 m/s

Final velocity = -18 m/s (opposite direction)

Let's calculate the initial momentum and final momentum:

Initial momentum = (5.69x10^-2 kg) * (13 m/s)

Final momentum = (5.69x10^-2 kg) * (-18 m/s)

Now, let's calculate the change in momentum:

Change in momentum = Final momentum - Initial momentum

Plugging in the values:

Change in momentum = [(5.69x10^-2 kg) * (-18 m/s)] - [(5.69x10^-2 kg) * (13 m/s)]

Performing the calculation will give you the change in the ball's momentum.

Hope I helped

The maximum height that a flea can jump can be determined using conservation of energy.  The flea can jump up to a height of about 5 cm.

The potential energy at the maximum height is equal to the initial kinetic energy. The initial kinetic energy is given by (1/2)mv², where m is the mass of the flea and v is its velocity.

First, we need to convert the mass of the flea from micrograms to kilograms, which gives m = 450 × 10⁻⁶ kg. The velocity of the flea is given as 1 m/s. Thus, the initial kinetic energy of the flea is given by (1/2) × 450 × 10⁻⁶ × (1 m/s)² = 0.225 × 10⁻³ J.

At maximum height, the kinetic energy of the flea is zero, and all its energy is in the form of potential energy. The potential energy at maximum height is given by mgh, where h is the maximum height. Equating the initial kinetic energy to the potential energy at maximum height, we get: 0.225 × 10⁻³ J = (450 × 10⁻⁶ kg) × (10 m/s²) × h

Simplifying, we get h = 0.0495 m, which is approximately 5 cm.

To know more about conservation of energy, refer here:

https://brainly.com/question/2137260#

#SPJ11

The gravitational potential energy of the lake is 1.35 × 10¹⁹ J, calculated using the formula mgh.

The gravitational potential energy of Hydroelectric of the lake, 1.35 × 10¹⁹ J, is much greater than the energy stored in a 9-megaton fusion bomb, which is equivalent to 3.76 × 10¹⁶ J. This shows the vast amount of energy that can be harnessed from hydroelectric power facilities.

Hydroelectric power facilities are a clean and renewable energy source that has the potential to provide a significant portion of the world's electricity. The energy stored in a hydroelectric power facility is proportional to the volume of water stored and the height of the water above the generators. The gravitational potential energy is converted to electric energy using generators which are powered by the force of the falling water.

The amount of energy stored in a 9-megaton fusion bomb is equivalent to the energy released by the detonation of 9 million tons of TNT. The energy released in a nuclear explosion is a result of the conversion of mass into energy according to Einstein's famous equation E=mc². The energy released in a fusion reaction is several orders of magnitude greater than that released in a chemical reaction.

Learn more about Hydroelectric

brainly.com/question/15228003

#SPJ11

If a star remains at a constant size and temperature for a long period of time, it is most likely to be true that the star generates about as much energy as it radiates.

If a star remains at a constant size and temperature for an extended period, it suggests that the star is in a state of equilibrium. In such a state, the energy generated by the star's internal processes, such as nuclear fusion, is balanced by the energy radiated into space. This equilibrium is crucial for maintaining the star's stability and preventing it from expanding or contracting over time. If the star were to generate more energy than it radiates, it would accumulate excess energy and eventually experience an imbalance, causing changes in size, temperature, or both. Likewise, if the star generated less energy than it radiates, it would gradually deplete its internal energy reserves. Therefore, the most likely scenario is that the star generates about as much energy as it radiates, maintaining a steady state.

Learn more about energy radiated here:

https://brainly.com/question/14007126

#SPJ11

The power intensity of radiation per unit wavelength emitted at a wavelength of 500.0 nm by a blackbody at a temperature of 10,000 K is 3.63 × 10⁻² W⋅m⁻²⋅nm⁻¹.

To determine the power intensity of radiation per unit wavelength emitted by a blackbody at a given temperature and wavelength, we can use Planck's law, which gives the spectral radiance of a blackbody as a function of its temperature and wavelength;

B(λ, T)=(2hc²/λ⁵) × 1/(exp(hc/λkT) - 1)

where; B(λ, T) is the spectral radiance of the blackbody at wavelength λ and temperature T

h is Planck's constant

c is the speed of light

k is the Boltzmann constant

To obtain the power intensity per unit wavelength, we need to multiply the spectral radiance by the wavelength and divide by the speed of light;

I(λ, T) = B(λ, T) × λ / c

Substituting λ = 500.0 nm

= 5.00 × 10⁻⁷ m and T

= 10,000 K, we get;

B(500.0 nm, 10,000 K) = (2hc²/λ⁵) × 1/(exp(hc/λkT) - 1)

= 1.09 × 10⁸ W⋅m⁻²⋅sr⁻¹⋅m⁻¹

I(500.0 nm, 10,000 K)

= B(500.0 nm, 10,000 K) × λ / c

= 3.63 × 10⁻² W⋅m⁻²⋅nm⁻¹

Therefore, the power intensity is 3.63 × 10⁻² W⋅m⁻²⋅nm⁻¹.

To know more about power intensity here

https://brainly.com/question/21505382

#SPJ4

The maximum charge on the capacitor is 0.185 μC and the charge on the capacitor at an instant when the current in the inductor is 0.500 mA will be 0.109 μC.

(a)  We can calculate [tex]Q_{max}[/tex] by using the equation [tex]Q_{max} =C*V_{max}[/tex].

Given C = 3.20μF

And we know, [tex]V_{max} = I_{max} * XL[/tex]

Here, Inductive reactance(XL) = 2πfL, where f is the resonant frequency.

We know,[tex]f=\frac{1}{2\pi \sqrt{LC} }[/tex]

So, f = 1 / [2π√(85.0 mH * 3.20 μF)] = 1.28 kHz

∴ Inductive reactance(XL) = 2πfL

                                           = 2π * 1.28 kHz * 85.0 mH = 68.3 Ω

Now, [tex]V_{max} = I_{max} * XL[/tex]

∴ Vmax = 0.850 mA * 68.3 Ω = 58.05 mV

Finally, the maximum charge on the capacitor can be calculated as,

Qmax = C * Vmax

          = 3.20 μF * 58.05 mV

          = 0.185 μC

Therefore, the maximum charge on the capacitor is 0.185 μC.

(b)  When the current in the inductor has a magnitude of 0.500 mA, the voltage across the inductor will be,

V = I * XL

  = 0.500 mA * 68.3 Ω

  = 34.15 mV

Now the charge at required instant i.e., when I = 0.500 mA

Q = C * V

   = 3.20 μF * 34.15 mV

   = 0.109 μC.

Therefore, the magnitude of the charge on the capacitor at an instant when the current in the inductor has magnitude 0.500 mA is 0.109 μC.

Learn more about capacitor here

brainly.com/question/24212501

#SPJ4

When carrying out a large sample test of H0:µ = 10 vs. H1:µ ≠ 10 using a p-value approach, we fail to reject H0 at the level of significance α when the p-value is: Greater than α (p-value > α)

Here's a step-by-step explanation:

1. State the null hypothesis (H0): µ = 10

2. State the alternative hypothesis (H1): µ ≠ 10

3. Determine the level of significance (α)

4. Conduct the large sample test and calculate the test statistic

5. Find the p-value associated with the test statistic

6. Compare the p-value with the level of significance (α)

7. If the p-value is greater than α (p-value > α), we fail to reject the nullhypothesis (H0) In conclusion, when the p-value is greater than the level of significance α, we fail to reject the null hypothesis H0: µ = 10.

Large sample size (sample size), namely the number of subjects needed in a study, is an important aspect of a study, because it determines the precision (accuracy) of estimates (estimates) of the population parameters studied.

Learn More About large sample at https://brainly.com/question/13777275

#SPJ11

a. The largest wavelength found in the scattered x-rays is 6.65×[tex]10^{-2}[/tex] nm

b.  The scattering angle at which the wavelength observed is 176.6 degrees

The wavelength of the scattered photon is given by the Compton scattering formula:

λ' - λ = h/mc(1-cosθ)

Where, λ = initial wavelength of the X-ray photon, λ' = wavelength of the scattered X-ray photon, h = Planck's constant, m = mass of the electron, c = speed of light, and θ = scattering angle

a. To find the largest wavelength found in the scattered X-rays, we need to determine the maximum change in wavelength, which occurs when the scattered photon is emitted at an angle of 180 degrees (backscattering). At this angle, cos(θ) = -1, and the Compton scattering formula simplifies to:

λ' - λ = 2h/mc

Substituting the values, we get:

λ' - 6.60×[tex]10^{-2}[/tex] nm = 2(6.63×[tex]10^{-34}[/tex] J.s)/(9.11×[tex]10^{-31}[/tex] kg)(3.00×[tex]10^{8}[/tex] m/s)

Solving for λ', we get:

λ' = 6.65×[tex]10^{-2}[/tex] nm

Therefore, the largest wavelength found in the scattered X-rays is 6.65×[tex]10^{-2}[/tex] nm.

b. To find the scattering angle at which this wavelength is observed, we can use the Compton scattering formula again, but this time we solve for θ:

cosθ = 1 - (h/mc)(1/λ' - 1/λ)

Substituting the values, we get:

cosθ = 1 - (6.63×[tex]10^{-34}[/tex] J.s)/(9.11×[tex]10^{-31}[/tex] kg)(3.00×[tex]10^{8}[/tex] m/s)(1/6.65×[tex]10^{-2}[/tex] nm - 1/6.60×[tex]10^{-2}[/tex] nm)

Solving for θ, we get:

θ = 176.6 degrees

Therefore, the largest wavelength found in the scattered X-rays is observed at a scattering angle of approximately 176.6 degrees.

Know more about Wavelength here :

https://brainly.com/question/10728818

#SPJ11

The magnitude of the electrostatic force between the two charges is approximately 5.29 x 10^-5 N. The force between these two charges is attractive.

(a) To find the magnitude of the electrostatic force between the two charges, we can use Coulomb's Law which states

that the force between two charges is proportional to the product of the charges and inversely proportional to the square of the distance between them. Mathematically, this can be expressed as:

F = k * (q1 * q2) / r^2

Where F is the electrostatic force, k is Coulomb's constant (9 x 10^9 Nm^2/C^2), q1 and q2 are the charges in Coulombs, and r is the distance between the charges in meters.

Plugging in the given values, we get:

F = 9 x 10^9 * [(7.66 x 10^-9) * (4.54 x 10^-9)] / (1.93)^2
F ≈ 5.29 x 10^-5 N

Therefore, the magnitude of the electrostatic force between the two charges is approximately 5.29 x 10^-5 N.

(b) To determine if the force is attractive or repulsive, we need to look at the signs of the charges. In this case, one charge is positive (7.66 nc) and the other is negative (4.54 nc). Opposite charges attract each other, while like charges repel each other. Therefore, the force between these two charges is attractive.

Learn more about electrostatic force here:-

https://brainly.com/question/31042490

#SPJ11

The energy released when 100 kg of deuterium and 150 kg of tritium are consumed in one year in a fusion reactor is approximately 8.4 x 10^16 joules.

Fusion reactions release energy according to Einstein's mass-energy equivalence formula (E=mc^2), where m is the mass difference between the reactants and products, and c is the speed of light. Deuterium-tritium fusion is one of the most promising reactions for practical fusion power. It releases more energy per reaction compared to other fusion reactions, making it an attractive choice for future fusion reactors. The energy released when 100 kg of deuterium and 150 kg of tritium are consumed in one year in a fusion reactor is approximately 8.4 x 10^16 joules.

learn more about energy here:

https://brainly.com/question/1932868

#SPJ11

The velocity of the launcher after the projectile is launched is approximately 1.96 m/s in the opposite direction.

When the projectile is launched, it experiences a forward momentum due to its horizontal velocity. According to the law of conservation of momentum, the total momentum before and after the launch must remain the same. Initially, the momentum of the system is given by the sum of the momentum of the projectile and the launcher. The momentum of the projectile is calculated as the product of its mass (0.050 kg) and its horizontal velocity (647 m/s), resulting in 32.35 kg·m/s. The momentum of the launcher is given by the product of its mass (4.65 kg) and its initial velocity (2.0 m/s), which is 9.3 kg·m/s. To maintain the total momentum, the launcher must gain an equal and opposite momentum when the projectile is launched. Therefore, the momentum of the launcher after the launch is -9.3 kg·m/s. Dividing this momentum by the mass of the launcher, we find that the velocity of the launcher after the projectile is launched is approximately -1.96 m/s in the opposite direction.

To learn more about velocity refer:

https://brainly.com/question/29110645

#SPJ11

To start a fire, the camper uses a lens with an 18 cm focal length to focus the sun's rays on a piece of wood.

The focal length of a lens determines its ability to converge or diverge light. In this case, the camper wants to concentrate sunlight onto a specific point on the wood, raising its temperature enough to ignite a fire. By placing the lens between the sun and the wood, the lens refracts and converges the sun's rays, forming a focused spot on the wood's surface. The focal length of 18 cm indicates that the lens will converge the light at a distance of 18 cm from its surface. By adjusting the position of the lens, the camper can position the focused spot on the wood, generating enough heat to ignite it and start a fire.

Learn more about determines here:

https://brainly.com/question/31755910

#SPJ11

To determine electrical energy from a plot of power versus time, you can integrate the power over time. The integral of power with respect to time gives you the total energy consumed or produced.

Here are the steps to determine electrical energy from a plot of power versus time:

1. Obtain a plot of power (P) as a function of time (t).

2. Identify the area under the power-time curve.

3. Calculate the integral of power with respect to time (∫P dt) over the desired time interval.

4. Evaluate the integral to find the numerical value of energy.

If the power values in the plot are constant over different time intervals, you can simply calculate the energy for each interval by multiplying the constant power by the duration of that interval.

Keep in mind that the unit of power should be consistent throughout the calculation (e.g., watts, kilowatts), and the resulting energy value will be in units such as joules or watt-hours (Wh) depending on the units used for power and time.

To know about determining electrical energy refer here

https://brainly.com/question/29562686#

#SPJ11

The angular acceleration of the object is 1 rad/s^2.

The angular acceleration (α) is given by the formula:

α = (ωf - ωi) / t

where ωi is the initial angular velocity, ωf is the final angular velocity, and t is the time taken for the change in angular velocity.

Substituting the given values, we get:

α = (8 rad/s - 3 rad/s) / 5 s = 1 rad/s^2

For more question on angular acceleration click on

https://brainly.com/question/13014974

#SPJ11

Therefore, the angular acceleration of the object is 1 [tex]rad/s^2[/tex]. This means that the object's angular velocity is changing by 1 rad/s every second.

Angular acceleration is the rate at which the angular velocity of an object changes. It is a vector quantity that is defined as the change in angular velocity divided by the time interval over which the change occurs. In other words, it is the rate of change of the object's angular velocity.

In the given problem, the object's angular velocity changes from 3 rad/s clockwise to 8 rad/s clockwise in 5 s. We can use the formula for angular acceleration, which is given by:

α = (ωf - ωi) / t

where α is the angular acceleration, ωf is the final angular velocity, ωi is the initial angular velocity, and t is the time interval over which the change occurs.

Substituting the given values, we get:

α = (8 rad/s - 3 rad/s) / 5 s

α = 1 [tex]rad/s^2[/tex]

if we were to plot the object's angular velocity as a function of time, we would see a linear increase in the angular velocity with a slope of 1 [tex]rad/s^2[/tex].

Learn more about angular acceleration here:

https://brainly.com/question/29428475

#SPJ11

The maximum diffraction order seen is m = 3.

To find the maximum diffraction order seen for a 500 lines per mm diffraction grating illuminated by light of      wavelength 620 nm, follow these steps:

Step 1: Convert lines per mm to lines per meter.
500 lines/mm = 500,000 lines/m

Step 2: Calculate the grating spacing (d) using the formula:
d = 1 / (lines per meter)
d = 1 / 500,000
d = 2 x 10^-6 m

Step 3: Use the diffraction formula to find the maximum order (m):
m * λ = d * sinθ

Since we want to find the maximum diffraction order, the angle θ will be at its maximum (90 degrees).

Therefore, sinθ = sin(90°) = 1.

Step 4: Solve for m:
m = (d * sinθ) / λ
m = (2 x 10^-6 * 1) / (620 x 10^-9)
m = 3.2258

Since the diffraction order must be an integer, the maximum diffraction order seen is m = 3.

Learn more about Diffraction https://brainly.com/question/13104464

#SPJ11