There is a solenoid with an inductance 0.285mH, a length of 36cm, and a cross-sectional area 6×10^−4m^2. Suppose at a specific time the emf is -12.5mV, find the rate of change of the current at that time.

Answers

Answer 1

The rate of change of current is given by the formula:

[tex]$$\frac{dI}{dt} = \frac{E}{L}$$[/tex]

where $E$ is the emf and $L$ is the inductance of the solenoid. Plugging in the given values, we get:

[tex]$$\frac{dI}{dt} = \frac{-12.5 \text{mV}}{0.285 \text{mH}} \approx -43.86 \text{A/s}$$[/tex]

Therefore, the rate of change of current at that specific time is approximately -43.86 A/s.

The rate of change of current in a solenoid is determined by the emf induced in the solenoid and the inductance of the solenoid. The emf induced in a solenoid is given by Faraday's Law, which states that the emf is proportional to the rate of change of the magnetic flux through the solenoid. The inductance of the solenoid depends on the geometry of the solenoid, which is given by its length and cross-sectional area. The formula for the rate of change of current is derived from the equation that relates the emf, the inductance, and the rate of change of current in an ideal solenoid. Plugging in the given values into this formula gives us the rate of change of current at that specific time.

Learn more about Faraday's Law here:

https://brainly.com/question/1640558

#SPJ11


Related Questions

Dr. Albert gets a spark from the static in the door knob. He is not hurt. However, the electric _____ is high.

Answers

Dr. Albert gets a spark from the static in the door knob. He is not hurt. However, the electric current is high.

What is the static spark?

Sparks that are considered "static" have a massive momentary current and power (momentary like less than a millionth of a second.) However, the overall wattage of these sparks is exceedingly low. It's really too little to harm your muscles with heat (or even any warming a thermometer could detect.)

Negative and positive charges in an object must balance out for static electricity to occur. These charges may accumulate on an object's surface until they can be released or discharged. They can be discharged via a circuit, for example.

Learn more about static spark here:

https://brainly.com/question/4045527

#SPJ4

What is the kinetic energy of an object with a mass of 10 kilograms traveling at a speed of 10 meters per second? Assume that no other forces act upon the object.
Group of answer choices

a. 50,000 J

b. 100 J

c. 500 J

d. 1000 J

Answers

The kinetic energy of an object with a mass of 10 kilograms traveling at a speed of 10 meters per second is 500J (option C).

How to calculate kinetic energy?

The kinetic energy of a body refers to the energy due to the motion of the body. The kinetic energy can be calculated using the following formula:

K.E = ½ × m × v²

Where;

K.E = kinetic energym = massv = speed

K.E = ½ × 10 × 10²

K.E = 5 × 100 = 500J

Therefore, the kinetic energy of an object with a mass of 10 kilograms traveling at a speed of 10 meters per second is 500J.

Learn more about kinetic energy at: https://brainly.com/question/12669551

#SPJ1

One similarity in the spectra of T dwarf stars and giant planets in our solar system is that their spectra show:

Answers

One similarity in the spectra of T dwarf stars and giant planets in our solar system is that their spectra show: "Indications of methane"

What is solar system?

The solar system is made up of planets, moon, asteroids, comets, dust, and gas that revolve around the sun, which is our nearest star.

It consists of the giant planets Jupiter and Saturn, the ice giant Uranus and Neptune, and the rocky core planets Mercury, Venus, Earth, and Mars.

Some key points of solar system are-

The solar nebula, a massive cloud of gas and dust, began to collapse in on itself some some 4.6 billion years ago, forming the solar system's star and planets. Scientists have used meteorites, or bits of space rock which have fallen on Earth, to determine the age of the universe. Some of these tiny fragments, which have fallen off of planets or moons, can provide intriguing scientific data regarding the makeup and past of their parent body. Since the beginning of the solar system, before the planet even existed, others have been orbiting the sun. The oldest meteorite is 4.55 billion years old and came to Earth in the Allende meteor, which was dispersed over Mexico in 1969.

To know more about Our Solar System, here

https://brainly.com/question/13979351

#SPJ4


Barry slides across an icy pond. The coefficient of kinetic friction between his
shoes and the ice is 0.15. If his mass is 83 kg, what is the force of friction
acting on him?
OA. 813 N
B. 1150 N
C. 122 N
D. 352 N

Answers

The force of friction acting on him is 122 N. The correct answer is option C

What is Friction ?

Friction is a force that opposes the motion of a static or a moving object.

Given that Barry slides across an icy pond. The coefficient of kinetic friction between his shoes and the ice is 0.15. If his mass is 83 kg

The given parameters are;

Mass m = 83 kgCoefficient of kinetic friction μ = 0.15Frictional force [tex]F_{r}[/tex] = ?

The normal reaction N on the body = mg

N = 83 x 9.8

N = 813.4 N

The Frictional force formula is  [tex]F_{r}[/tex] = μN

[tex]F_{r}[/tex] = 0.15 x 813.4

[tex]F_{r}[/tex] = 122.01 N

Therefore, the force of friction acting on him is 122 N approximately.

Learn more about Friction here: https://brainly.com/question/24338873

#SPJ1

Some tornadoes have central downdrafts that accompany the massive rotating updrafts.
a. True
b. False

Answers

Some Tornadoes have central downdrafts that accompany the massive rotating updrafts. True

Mid-altitude winds come into the storm from the rear (or on the west or southwest side). As this dry, cool air enters the system, rain evaporates, cooling it even more. The cooling air becomes cooler than the surrounding air, sinks, and forms a strong downdraft.

Updrafts characterize a storm's early development, during which warm air rises to the level where condensation starts and precipitation starts to expand. In a mature storm, updrafts are present alongside downdrafts caused by cooling and falling precipitation.

Learn more about Tornadoes here https://brainly.com/question/18155172

#SPJ4

What is the term for the principal that an object in motion remains in motion until it is met by an outside force?

Answers

The term for the principal that an object in motion remains in motion until it is met by an outside force is called inertia

Newton's first law states that if a body is at rest or moving at a constant speed in a straight line, it will remain at rest or keep moving in a straight line at constant speed unless it is acted upon by a force .This principal is named as inertia .

Every matter have inertia , a property to remain in that very position until unless it is been forced on them to change their position .

Inertia is a property of matter that causes it to resist changes in velocity (speed and/or direction). According to Newton's first law of motion, an object with a given velocity maintains that velocity unless acted on by an external force. Inertia is the property of matter that makes this law hold true.

To learn more about inertia here

https://brainly.com/question/1358512?referrer=searchResults

#SPJ4

A block is thrown with an initial velocity of 30.0 m/s at an angle of 25.0o above the horizontal. What is the highest elevation reached by the ball in its trajectory in meter

Answers

The highest elevation reached by the ball in its trajectory is 16.4 m.

To find the answer, we need to know about the maximum height reached in a projectile.

What's the mathematical expression of the maximum height reached in a projectile motion?

The maximum height= U²× sin²(θ)/gU= initial velocity, θ= angle of projectile with horizontal and g= acceleration due to gravity

What's the maximum height reached by a block that is thrown with an initial velocity of 30.0 m/s at an angle of 25° above the horizontal?

Here, U = 30.0 m/s and θ= 25°Maximum height= 30²× sin²(25)/9.8

= 16.4m

Thus, we can conclude that the highest elevation reached by the ball in its trajectory is 16.4 m.

Learn more about the projectile motion here:

brainly.com/question/24216590

#SPJ4

A force of 50 n is used to push a wheelchair forward at constant velocity. if the wheelchair is displaced 0.5 m each second, what is the mechanical power expended when transporting the wheelchair?

Answers

The mechanical power expended when transporting the wheelchair is 25 Watts

What is power?

Power is defined as  the amount of energy transferred or converted per unit time. The unit of power is measured in Watts. The higher units are kilowatts, megawatts etc.

The formula for calculating the power expended is expressed as:

Power = Workdone/Time

Since workdone = force * distance, the formula for power will be:

Power = Force*distance/Time

Given the following parameters

Force = 50N

distance = 0.5m

time = 1 second

Substitute to determine the power

Power = 50*0.5/1

Power = 25/1

Power = 25Watts

Hence the mechanical power expended when transporting the wheelchair is 25 Watts

Learn more on power here; https://brainly.com/question/24858512

#SPJ1

Because white dwarfs are small, as their name implies, they are hard to see. What is a way astronomers have to find white dwarfs that distinguishes them from main sequence stars

Answers

Astronomers find white dwarfs that distinguish them from main sequence stars because white dwarfs get really hot, we can search for their ultraviolet radiation.

What is a white dwarf?

A white dwarf is a very hot star that radiated much energy in the form of ultraviolet radiation.

This UV radiation is initially very bright and then these stars become red with time.

In conclusion, Astronomers find white dwarfs they can search for their ultraviolet radiation.

Learn more about white dwarfs here:

https://brainly.com/question/19602278

#SPJ1

derric climbs onto his roof to hang Christmas light. If the roof is 4.3 meters from the ground and derrick gains 2730 J of potential energy while climbing, what is his mass​

Answers

Mass of Derrick at a height 4.3 m having 2730 joule of energy is 65 Kg.

What is the expression of gravitational potential energy near the earth surface?Mathematically, gravitational potential energy near the earth surface= m×g×hm= mass of Derrick, g= acceleration due to gravity, h= height at which Derrick present Then, mass (m) of Derrick = potential energy/ (g×h)

What is the mass of Derrick, if he gains 2730 joule of energy at 4.3m above the ground?

Mass of Derrick= 2730/(9.8×4.3)

= 65 kg

Thus, we can conclude that the mass of Derrick is 65 Kg.

Learn more about the gravitational potential energy here:

brainly.com/question/26588957

#SPJ1

Even though the Sun gets lower in the sky after solar noon, and the intensity of incident solar radiation is reduced, the air temperature continues to climb after solar noon because

Answers

Even though the Sun gets lower in the sky after solar noon, and the intensity of incident solar radiation is reduced, the air temperature continues to climb after solar noon because energy is still being absorbed by the ground faster than it is being lost

Solar radiation is a broad word for the electromagnetic radiation that the sun emits. It is also sometimes referred to as the solar resource or just sunshine. A multitude of devices can be used to catch solar radiation and transform it into useful forms of energy, such as heat and electricity.

The energy that the Sun emits into space in the form of electromagnetic waves is known as solar radiation. This energy, which is released by the Sun's surface, affects climatological and atmospheric processes. Visible light, ultraviolet light, infrared, radio waves, X-rays, and gamma rays are all types of solar radiation.

Cardiovascular disease can be caused by radiation by altering the cardiovascular system, harming the heart, hardening and narrowing arteries, and/or removing part of the cells from the blood vessel linings.

To learn more about solar radiation please visit -
https://brainly.com/question/23338147
#SPJ4

Modern methods of massively parallel sequencing include devices for detecting fluorescence or visible light as each:

Answers

Modern methods of massively parallel sequencing include devices for detecting fluorescence or visible light as each nucleotide is incorporated during synthesis.

Each nucleotide is marked with fluorescent dye, and a some traces of fluorescent intensities helps identify sequences.

What is nucleotide?

Nucleotides are organic compounds made up of a phosphate and a nucleoside.They function as monomeric units of the key macromolecules found in all living forms on Earth, deoxyribonucleic acid (DNA), and ribonucleic acid (RNA), which are both nucleic acid polymers. In addition to being produced by the liver from common nutrients, nucleotides can also be received through diet. A nucleobase, a five-carbon sugar (ribose or deoxyribose), and a phosphate group made up of one to three phosphates are the three component molecules that make up a nucleotide. Guanine, adenine, cytosine, and thymine are the four nucleobases found in DNA; uracil is used in place of thymine in RNA.On a fundamental, biological level, nucleotides are also essential to metabolism. They supply chemical energy throughout the cell in the form of the nucleoside triphosphates adenosine triphosphate (ATP), guanosine triphosphate (GTP), cytidine triphosphate (CTP), and uridine triphosphate (UTP).These are necessary for the synthesis of amino acids, proteins, and cell membranes as well as for moving the cell and its components (both internally and between cells), cell division, and other cellular processes.Nucleotides are also key cofactors in enzyme activities and take role in cell signaling (cyclic guanosine monophosphate, or cGMP, and cyclic adenosine monophosphate, or cAMP).

Know more about nucleotide https://brainly.com/question/13185536

#SPJ4

A car drives 17.9 m/s east. It
accelerates at 2.88 m/s² at a
137.7° angle. How long does it
take until the car is driving directly
north?

Answers

The time taken for the car to drive directly north is 8.52 seconds.

Time of motion of the car

v = u + at

At 137.7° angle

v = u + a cosθ(t)

v = 17.9 + 2.88cos(137.7)t

v = 17.9 - 2.1t

when the car is directly north, v = 0

0 =  17.9 - 2.1t

2.1t = 17.9

t = 17.9/2.1

t = 8.52 seconds

Thus, the time taken for the car to drive directly north is 8.52 seconds.

Learn more about time of motion here: https://brainly.com/question/2364404

#SPJ1

Clouds lose their __________ when the surrounding air temperature equals the rising air temperature.

Answers

Clouds lose their stability when the surrounding air temperature equals the rising air temperature.

When vapor condenses and produces the billowing columns, the ascending air, which is still warmer than the nearby air, rises. occurs when radiation even during night cools the Earth's surface as well as the air around.

As a result, the air parcel can increase until all of the latent heat has already been released as well as the "surplus" water vapor has condensed. Hence, the fundamental factor that prevents clouds from rising is the cessation of the production of heat transfer through condensation.

To know more about air.

https://brainly.com/question/19368011

#SPJ4

The same bungee jumper from the previous question is now safely back on the ground, but hungry. He eats an apple before going for another jump. What energy transfer is he experiencing?

Group of answer choices

a. Kinetic to chemical

b. Elastic potential to chemical

c. Chemical to gravitational potential

d. Chemical to kinetic

Answers

D. The energy transfer he is experiencing is Chemical to kinetic.

Conservation of energy

The principle of conservation of energy states that energy can neither be created nor destroyed but can be converted from one form to another.

The apple eaten by the bungee jumper will provide chemical energy which will be converted into kinetic energy of the jumper once he is in motion.

Thus, the energy transfer he is experiencing is Chemical to kinetic.

Learn more about kinetic energy here: https://brainly.com/question/25959744

#SPJ1

A cart that is rolling at a constant velocity on a level table fires a ball straight up out of a vertical tube.

Answers

If the cart is accelerating in the forward direction the ball would fall behind the tube.

What is meant by acceleration?

The rate at which the speed and direction of a moving object vary over time. A point or object going straight ahead is accelerated when it accelerates or decelerates.

Some key features of acceleration are-

Any procedure where the velocity varies is referred to as acceleration. There are just two ways to accelerate: changing your speed or changing your direction, or changing both. This is because velocity is both a speed as well as a direction.No matter how quickly you're moving, if you're not altering your direction or speed, you can't possibly be accelerating.In a car, accelerating may be accomplished by applying the gas pedal or the brakes, both of which would result in changes in speed. However, you could also turn by turning the steering wheel, which would reverse your momentum. Given that they alter velocity, any of them would be seen as an acceleration.

The formula of acceleration is -

[tex]a=\frac{\Delta v}{\Delta t}=\frac{v_{f}-v_{i}}{\Delta t}[/tex]

[tex]v_{f}[/tex] is the final velocity

[tex]v_{i}[/tex] is the initial velocity

Δt is total time between both velocities.

To know more about the acceleration, here

https://brainly.com/question/460763

#SPJ4

The complete question is-

A cart that is rolling at a constant velocity on a level table fires a ball straight up out of a vertical tube. Does your answer change if the cart is accelerating in the forward direction? If so, how?

Question 5 of 32
According to the periodic table below, which element has the largest average
atomic mass?
OA. Helium (He)
OB. Oxygen (0)
OC. Nitrogen (N)
OD. Neon (Ne)

Answers

The answer is D
Neon has 20.0026 element more then the other

Analog signals from sensors are changed to digital signals for processing by the computer through which type of circuit?

Answers

Analog signals from sensors are changed to digital signals for processing by the computer through analog to digital converter circuit.

What is a Circuit?

This is referred to as a path in which electric current flows and comprises of components such as resistor, capacitor etc.On the other hand, analog to digital converter circuit is responsible for the conversion of the analog signals to digital or binary forms and is read through the use of a microcontroller.

The digital signal is what is in vogue as of today due to its synergy with modern electric devices which are common in today's world which explains the need for the conversion to this type of signal.

This is therefore the reason why analog to digital converter circuit was chosen as the most appropriate choice in this type of scenario.

Read more about Analog to digital converter here https://brainly.com/question/24750760

#SPJ1

What are the different mechanisms for transferring energy to or from a control volume?

Answers

The different mechanisms for transferring energy to or from a control volume is heat , work and mass .

According to the question

Definition of energy :

The basic definition of energy is capacity to do work.

Types of energy :

The energy can be of various types which can be- heat energy, internal energy, electrical energy, chemical energy and nuclear energy.

The transformation of energy :

The transformation of energy is the conversion mechanism of energy from one form to another. During the transformation process, some portion of the energy is converted into the useless form known as dissipation of energy .

The different mechanisms which transfer energy to or from control volume are:

1, heat

2 .work

3. mass.

Hence, the different mechanisms for transferring energy to or from a control volume is heat , work and mass .

To know more about energy here:

https://brainly.com/question/1932868

#SPJ4

how do you use atomic models​

Answers

1234567891011121314151617181920

A microwave is a(n) _____ that is directed from one microwave station tower to another

Answers

The high-frequency radio signal is the answer.

Radiofrequency (RF) radios are in the wavelength band of 100 to 10 meters and extend from 3 MHz to 30 MHz. Much of the HF bandwidth is allocated to mobile and fixed voice communications services that require transmission bandwidth of less than 12 kHz. International (Shortwave) Broadcast

Radio Frequency (HF) is an ITU term for the range of high-frequency electromagnetic waves (radio waves) from 3 to 30 MHz (MHz). It is also known as the decameter band or decameter wave because it has wavelengths in the range of 1 to 10 decameter (tens to hundreds of meters).

Learn more about radio waves here:https://brainly.com/question/69373

#SPJ4

Which type of graph could be easily converted into a pie chart?
A. Variable plot
B. Scatter plot
C. Bar graph
D. Line graph

Answers

Answer:

D.Linegraph

Explanation:

Linegraph could be easily converted into a pie chart

Answer:

bar graph

Explanation:

if the force acting on a body of mass 40 kg is doubled . by how much will the acceleration change

Answers

The acceleration will be doubled because the force and the acceleration are directly proportional please make my answer the brainliest. Thanks :)

Using the criteria you described in your previous answer, how would you compare solar power to fossil fuel power?

Answers

Solar power differ to fossil fuel power in that solar power is a much more optimal resource than fossil fuels

Solar power; however provides much more energy than fossil fuel powerInterestingly too, solar power resource can be used without releasing greenhouse gases compared to fossil fuels powerInfact, solar energy is the most reliable

What is renewable energy?

Renewable energy simply refers to energy that is not depleted when used. An example of such is solar power.

So therefore, solar power differ to fossil fuel power in that solar power is a much more optimal resource than fossil fuels

Learn more about renewable energy:

https://brainly.com/question/79953

#SPJ1

An energy storage system based on a flywheel (a rotating disk) can store a maximum of 3.7 MJ when the flywheel is rotating at 16000 revolutions per minute.

Answers

The moment of inertia of the flywheel is 2.63 kg-[tex]m^{2}[/tex]

It is given that,

The maximum energy stored on the flywheel is given as

E=3.7MJ= 3.7×[tex]10^{6}[/tex] J

Angular velocity of the flywheel is 16000[tex]\frac{rev}{min}[/tex] = 1675.51[tex]\frac{rad}{sec}[/tex]

So to find the moment of inertia of the flywheel. The energy of a flywheel in rotational kinematics is given by :

E = [tex]\frac{1}{2}[/tex][tex]Iw^{2}[/tex]

By rearranging the equation:

I = [tex]\frac{2E}{w_{2} }[/tex]

I = 2.63 kg-[tex]m^{2}[/tex]

Thus the moment of inertia of the flywheel is 2.63 kg-[tex]m^{2}[/tex].

Learn more about moment of inertia here;

https://brainly.com/question/13449336

#SPJ4

The volume of gas in a flexible container at a depth of 10 m/33 ft will expand to ______ its original volume if taken to the surface. Select one: Twice. Three times. Four times. None of the above.

Answers

The volume of gas in a flexible container at a depth of 10 m/33 ft will expand to double its original volume if taken to the surface.

What is volume:

The amount of space that a substance or object occupies.

Volume is denoted with letter V

What is a gas molecule?

Generally, a gas molecule is simply defined as a combination of numbers of atoms that are connected one to another.

here, 10 m/33 feet of sea water is taken to exerts a gauge pressure that is the same pressure as the atmosphere.

This means that we add one atmosphere/bar pressure for every 10 m/33 feet you descend.

The effect of this is that,

at 10 m/33 ft absolute pressure is two ata/bar

Adding another 10 m/33 ft to this depth to make it 20 m/66 ft, puts you under under three ata/bar of pressure and so on.

Descending to a depth it means that you have double the ata/bar pressure acting on you. If you decide to resurface, the pressure on the flexible container will reduce by a factor of two.

Since volume is inversely proportional to the pressure,

If the pressure reduces by a factor of 2, then the volume will increase by a factor of two.

Learn more about volume of gas here:

https://brainly.com/question/17328636

#SPJ4

A relief plane flying horizontally at 65.0 m/s is delivering a
food package to people stranded on an island. If the
island is a horizontal distance of 789 m away,
how high is the plane?
(Unit = m)
22000
Ay (m)
mily

Answers

The height of the plane delivering a food package to people stranded on an island is 722.2 m.

Time of motion of the food package

The time taken for the food package to hit the ground level is calculated as follows;

X = vt

where;

X is horizontal distance traveled by the food packagev is horizontal distancet is time of motion

t = X/v

t = 789/65

t = 12.14 seconds

Height of the plane

h = ¹/₂gt²

where;

h is height of fall of the food package which is height of the planet is time of motion of food packageg is acceleration due to gravity

h = (0.5)(9.8)(12.14²)

h = 722.2 m

Thus, the height of the plane delivering a food package to people stranded on an island is 722.2 m.

Learn more about height here: https://brainly.com/question/1739912

#SPJ1

Answer:

722.2

Explanation:

Jim climbs up a rope from an initial height of 1.30 m to a final height of 3.20 m. If Jim's mass is 45 kg, what is the change in his gravitational potential energy? Group of answer choices 1980 J 187 J 85.5 J 838 J

Answers

The change in the gravitational potential energy of the boy is 838 J.

So the correct choice is 838 J.

What is gravitational potential energy?

The energy possessed by an object due to its position from the chosen reference point when gravity is acting on that object is called gravitational potential energy.

The formula to calculate the difference in the potential energy is given by the formula,

U=m*g*h

where U is the difference in the potential energy, m is the mass, g is the acceleration due to gravity, and h is the height difference between the initial height and the final height.

The height difference is given by the formula,

h=h2-h1

where h2 is the final height and h1 is the initial height.

Given that the initial height is 1.30 m and the final height is 3.20 m, substitute h1=1.30 m and h2=3.20 m in the formula of height to calculate the height difference.

h=3.20-1.30

h=1.90 m

The mass of the boy is 45 kg and the value of g is 9.8 m/s^2. Substitute m=45 kg, g=9.8 m/s^2, and h=1.90 m in the formula of the gravitational potential energy to calculate the difference in the gravitational potential energy.

U=45*9.8*1.90

U=837.9 J

U≈838

Learn more about the gravitational potential energy:

https://brainly.com/question/16155035

#SPJ4

Edwin hubble was able to show that (with the exception of our nearest neighbors) the farther a galaxy is from us, the?

Answers

Edwin hubble was able to show that (with the exception of our nearest neighbors) the farther a galaxy is from us, the faster it is moving away from us.

Hubble ultimately demonstrated that, contrary to the widely accepted belief that the universe is static, galaxies are actually moving away from us. Hubble noticed that the light appeared to be shifted toward the red end of the spectrum by observing the light coming from distinct galaxies.

Hubble made the amazing discovery that a galaxy's redshift exactly correlated with its distance from the earth. That implied that objects farther from Earth were dispersing more quickly. To put it another way, the cosmos must be growing. In 1929, he made his discovery public.

Learn more about galaxy here;

https://brainly.com/question/2905713

#SPJ1

Five stars are shown on the following H-R diagrams. Rank the stars based on their surface temperature from highest to lowest. If two (or more) stars have the same surface temperature, drag one star on top of the other(s).

Answers

All five stars appear at the same place along the horizontal axis showing spectral type.

Because spectral type is related to surface temperature, all five stars must have the same surface temperature.

Now proceed to Part C to determine how these stars vary in luminosity.

What is a Star?

This refers to the heavenly body that is a natural luminous body that is visible in the sky, especially at night

Hence, we can see that based on the ranking of stars, the surface temperature of each star is taken into account, and based on their spectral type, the stars all have the same temperature.

Therefore, to show the difference between the stars, their luminous intensity needs to be analyzed,

Read more about stars here:

https://brainly.com/question/1320222

#SPJ1

Other Questions
All EXCEPT one are the characteristics of Romantic Arts. 1 pointDramatic compositionWeight of actionHeightened sensationEmotional extremes A person's inner abilities to solve problems, alter self-concept, and become more self-directed reflect roger's concept of the If a certain PWM waveform with a 30 % duty cycle has an RMS voltage of Vrms=Vrms= 1 VV, what will be the RMS voltage if the duty cycle changes to 90 %? true/false. paychex provided direct deposit payroll services for ophtalmic surgeons T/F : productions that consist almost entirely of expressive movement, dance, music, and light are referred to as physical theatre. What is the empirical formula of a compound that contains 0.783 g of carbon, 0.196 g of hydrogen, and 0.521 g of oxygen? With both resistance and aerobic training, children exhibit a(n) ______________ in fat mass and a(n) ________________ in fat-free mass.a) decrease, decreaseb) increase, plateauc) decrease, increased) increase, decrease question 1remembering that the latin suffix -tion means "the state or condition of" and the latin root appararemeans "to appear" use the context clues provided in the passage to determine the meaning ofapparition. write your definition of "apparition here and tell how you got it. A resistor is made from a hollow cylinder of length, l, innerradius a, and outer radius b. The region a Each bit operation is completed in 10 9seconds. You have one second to calculate the value of some function f(n) for the largest possible value of n. a) If calculating f(n) takes nlog 2(n) big operations, then the largest value of n for which f(n) could be computed in one second is n=. (Round to the nearest million) b) If calculating f(n) takes n 2big operations, then the largest value of n for which f(n) could be computed in one second is n=. (Round to the nearest thousand) c) If calculating f(n) takes 2 nbit operations, then the largest value of n for which f(n) could be computed in one second is n=. (Round to the nearest whole number) Which of the following best explains the behavior of the guard squirrels? A. The behavior of the guard squirrels increases the survival of close relatives that share the genes of the guard squirrels. B. Guard squirrels typically have recessive alleles, and by sacrificing themselves, they lessen the chance that recessive alleles will get passed on. C. Guard squirrels are typically females who have already reproduced, so they are no longer needed by the group. D. The guard squirrels confuse the predator, lowering the predators success rate because the predator cannot tell determine the volume of so2 (at stp; in liters) formed from the reaction of 96.7 g of fes2 and 55.0 l of o2 (at 398 k and 1.20 atm). find the gss of the following 3 des: 2 = 0 If O is the center of the above circle, H is the midpoint of EG and D is the midpoint of AC, what is the ( Air is compressed in an Otto cycle beginning at 35 C and 0.1 MPa. The maximum temperature of the process is 1100 C and the compression ratio is 7. Find (a) the pressure and temperature at all points of the cycle, (b) the heat that must be supplied to the process per unit mass (kg) of air, the work done per unit mass of air, and (c) the efficiency of the cycle. Write your own MATLAB code to perform an appropriate Finite Difference (FD) approximation for the second derivative at each point in the provided data. Note: You are welcome to use the "lowest order" approximation of the second derivative f"(x). a) "Read in the data from the Excel spreadsheet using a built-in MATLAB com- mand, such as xlsread, readmatrix, or readtable-see docs for more info. b) Write your own MATLAB function to generally perform an FD approximation of the second derivative for an (arbitrary) set of n data points. In doing so, use a central difference formulation whenever possible. c) Call your own FD function and apply it to the given data. Report out/display the results. a particular light photon carries an energy of 3 x 10-19 j. what are the frequency, wavelength, and color of this light? what is the probability that z is between 1.57 and 1.87 If Gestalt is, "The total is greater than the sum of its parts", then what is the word for "The total is less than the sum of its parts?" Thanks if we find that the null hypothesis, h0:j=0h0:j=0, cannot be rejected when testing the contribution of an individual regressor variable to the model, we usually should: