unpolarized light passes through two plarizing filters. initial intensity of the beam is 350 w/m2 . after the beam passes through both polarizing filter its intensity drops to 121 w/m2 .
What is the angle from the vertical of the axis of the second polarizing filter?

The amount of charge needed to create this situation is approximately 8.9876 x 10⁹ Coulombs.

It should be noted that 5.6104 x 10²⁸ elementary charges are needed to create this charge.

According to Coulomb's Law, the force of attraction or repulsion between two charges is proportional to the product of their magnitudes and inversely proportional to the square of their distance.

q = 1/4πε₀ ≈ 8.9876 x 10⁹ C

The amount of charge needed to create this situation is approximately 8.9876 x 10⁹ Coulombs.

Also, the number of elementary charges needed to create the charge calculated in the previous question is:

n = q/e = (8.9876 x 10⁹ C) / (1.6022 x 10^-¹⁹ C) ≈ 5.6104 x 10²⁸

Learn more about charge on

https://brainly.com/question/18102056

#SPJ1

If you flew a spaceship straight into Jupiter, aiming toward its center, the spaceship would experience increasing atmospheric pressure, temperature, and density as it descends. Initially, the spacecraft would encounter the outer layers of Jupiter's atmosphere, which is primarily composed of hydrogen and helium. As it progresses further, it would experience more intense pressure, leading to the hydrogen gas transitioning into a liquid state.

Eventually, the spacecraft would reach a layer where metallic hydrogen is present, which is due to the extremely high pressure and temperature conditions deep within Jupiter's interior. The intense conditions in this region would likely cause the spacecraft to be crushed and destroyed by the immense pressure and heat.

Throughout the descent, the spacecraft would also encounter strong winds and powerful storms, such as the Great Red Spot, which could further challenge its integrity and ability to withstand Jupiter's harsh environment. Overall, the spaceship's journey into Jupiter would be a perilous one, and it would ultimately be destroyed by the planet's extreme conditions.

To know more about spaceship click this link-

https://brainly.com/question/14198872

#SPJ11

a) approximately 23.995 m of space should be left between adjacent rails for them to touch on a summer day.

b) The stress in the rails on a summer day when their temperature is 33.0°C is approximately 8.8 MPa.

(a) To calculate the space needed between adjacent rails for them to touch on a summer day, we can use the coefficient of thermal expansion for steel, which is approximately 1.2 × 10⁻5 /°C

First, we need to calculate the change in length of each rail segment from -2.0°C to 33.0°C:

ΔL = αLΔT

ΔL = (1.2 × 10⁻⁵ /°C) × (12.0 m) × (33.0°C - (-2.0°C))

ΔL = 0.00528 m

So, each rail segment will expand by 0.00528 m on the summer day. To determine the space needed between adjacent rails, we subtract the expanded length of one rail from the original length of two rails:

Space needed = (2 × 12.0 m) - 0.00528 m

Space needed = 23.99472 m

Therefore, approximately 23.995 m of space should be left between adjacent rails for them to touch on a summer day.

(b) If the rails are originally laid in contact, they will expand by a total of 0.01056 m on the summer day. The stress in the rails can be calculated using the formula:

Stress = Young's modulus × (change in length / original length)

Assuming a Young's modulus of 200 GPa for steel, we get:

Stress = (200 × 10^9 Pa) × (0.01056 m / (12.0 m × 2))

Stress = 8.8 × 10^6 Pa

Therefore, the stress in the rails on a summer day when their temperature is 33.0°C is approximately 8.8 MPa.

To learn more about Young's modulus  here

https://brainly.com/question/13257353

#SPJ4

Yes, there does appear to be an externality associated with tire production.

This is because tire production often involves the release of pollutants and emissions into the environment, which can have negative effects on the health and well-being of individuals and ecosystems. Additionally, the disposal of tires can also lead to environmental damage if they are not properly recycled or disposed of. Therefore, the costs of tire production and disposal are not fully borne by the producers and consumers of tires, but also by society as a whole, making it an example of a negative externality.

To learn more about Tire Production, visit:

https://brainly.com/question/30126682

#SPJ11

The proof that some IR waves penetrate Earth's atmosphere and reach the surface is that we feel the warmth of the Sun .

]There are multiple pieces of evidence that suggest that at least some IR waves penetrate Earth's atmosphere and reach the surface. First, cell phones are able to receive signals even on cloudy days, which indicates that some form of electromagnetic radiation is able to pass through the atmosphere.

Additionally, people are able to get sunburns on their skin, which is caused by exposure to UV radiation from the Sun. This further supports the idea that some wavelengths of radiation are able to penetrate the atmosphere. Another piece of evidence is that we are able to see stars at night, which indicates that some light is able to travel through the atmosphere and reach our eyes.

Finally, we are able to feel the warmth of the Sun, which is caused by infrared radiation reaching the surface of the Earth. All of these observations suggest that at least some types of electromagnetic radiation are able to penetrate Earth's atmosphere and reach the surface.

To know more about Wave refer here :

https://brainly.com/question/13874687

#SPJ11

The electron drift velocity is defined as the average velocity of electrons moving through a wire due to an applied electric field. Therefore, the answer is C.1/4.

This velocity depends on the wire's cross-sectional area, the current passing through it, and the number density of free electrons in the wire.

When the wire radius is halved, the cross-sectional area of the wire is reduced by a factor of 4 (since the area of a circle is proportional to the square of its radius). This means that the wire can accommodate fewer electrons, and so the number density of free electrons in the wire increases by a factor of 4.
When the current passing through the wire is doubled, the force on the electrons is increased, and so the electrons move faster. The relationship between current, force, and electron drift velocity is given by the equation v = (I/neA), where v is the electron drift velocity, I is the current, n is the number density of free electrons, e is the charge of an electron, and A is the cross-sectional area of the wire.
Plugging in the new values, we get:
v' = (2I)/(4neA/2)
v' = (2I)/(2neA)
v' = I/neA
This means that the electron drift velocity does not change when the wire radius is halved and the current is doubled.

For more such question on electron

https://brainly.com/question/371590

#SPJ11

The electron drift velocity in a wire is directly proportional to the current and inversely proportional to the wire radius.

If the wire radius is halved, the electron drift velocity will be doubled, and if the current is doubled, the electron drift velocity will also be doubled. Therefore, the overall change in the electron drift velocity would be a factor of 4, and the correct answer is B.4.
If both the wire radius is halved and the current is doubled, the electron drift velocity changes by a factor of A.2 B.4 C.1/4 D.1/8 E.8.
To answer this, let's consider the formula for current (I) in a wire:
I = n * A * e * v
where:
- I = current
- n = number of free electrons per unit volume
- A = cross-sectional area of the wire
- e = charge of an electron
- v = electron drift velocity
When the wire radius is halved, the cross-sectional area (A) is reduced by a factor of 4, because A = π * r^2.
When the current is doubled, I = 2 * I₀, where I₀ is the initial current.
Now, let's compare the initial and new situations:
I₀ = n * A₀ * e * v₀
2 * I₀ = n * (A₀ / 4) * e * v₁
Divide the second equation by the first:
2 = (1/4) * (v₁ / v₀)
Solve for the ratio of the new drift velocity (v₁) to the initial drift velocity (v₀):
v₁ / v₀ = 8
So, the electron drift velocity changes by a factor of 8 (Option E).

Visit here to learn more about electron drift velocity:

brainly.com/question/1599996

#SPJ11

(a) To find the magnification, we first need to determine the image distance (q). We can use the lens formula:
1/f = 1/p + 1/q

where f is the focal length (0.140 m), p is the object distance (0.240 m), and q is the image distance. Rearranging the formula to solve for q:
1/q = 1/f - 1/p
1/q = 1/0.140 - 1/0.240
1/q = 0.00714
q = 1/0.00714 ≈ 0.280 m
Now, we can find the magnification (M) using the formula:
M = -q/p
M = -0.280/0.240
M = -1.17
The magnification is -1.17.
(b) To find the image height (h'), we can use the magnification formula:
h' = M × h
where h is the object height (0.064 m). Plugging in the values:
h' = -1.17 × 0.064
h' ≈ -0.075 m
The image height is approximately -0.075 meters. The negative sign indicates that the image is inverted.

To know more about magnification visit:

https://brainly.com/question/21370207

#SPJ11

The minimal energy of photons that can be absorbed at the edges of the visible radiation range is approximately 3.11 eV for violet light and 1.77 eV for red light.

The edges of the visible radiation range are typically defined by the wavelengths of approximately 400 nm (violet) and 700 nm (red). To calculate the minimal energy of photons that can be absorbed at these edges, we can use the energy-wavelength relationship for photons:

[tex]\[ E = \frac{hc}{\lambda} \][/tex]

where \( E \) is the energy of the photon, \( h \) is the Planck's constant[tex](\( 6.626 \times 10^{-34} \, \text{J s} \))[/tex] , \( c \) is the speed of light [tex](\( 3.00 \times 10^{8} \, \text{m/s} \)[/tex]), and [tex]\( \lambda \)[/tex]is the wavelength of the photon.

First, we convert the wavelength values to meters:

[tex]\( \lambda_{\text{violet}} = 400 \, \text{nm} = 400 \times 10^{-9} \, \text{m} \)\( \lambda_{\text{red}} = 700 \, \text{nm} = 700 \times 10^{-9} \, \text{m} \)[/tex]

Now, we can calculate the minimal energies:

[tex]\( E_{\text{violet}} = \frac{hc}{\lambda_{\text{violet}}} \)\( E_{\text{red}} = \frac{hc}{\lambda_{\text{red}}} \)[/tex]

Substituting the values:

[tex]\( E_{\text{violet}} = \frac{6.626 \times 10^{-34} \, \text{J s} \times 3.00 \times 10^{8} \, \text{m/s}}{400 \times 10^{-9} \, \text{m}} \)[/tex]

[tex]\( E_{\text{red}} = \frac{6.626 \times 10^{-34} \, \text{J s} \times 3.00 \times 10^{8} \, \text{m/s}}{700 \times 10^{-9} \, \text{m}} \)[/tex]

Calculating these values:

[tex]\( E_{\text{violet}} \approx 4.97 \times 10^{-19} \, \text{J} \)[/tex]

[tex]\( E_{\text{red}} \approx 2.83 \times 10^{-19} \, \text{J} \)[/tex]

Finally, to convert the energies to electron volts (eV), we use the conversion factor:

[tex]\( 1 \, \text{eV} = 1.602 \times 10^{-19} \, \text{J} \)[/tex]

Converting the energies:

[tex]\( E_{\text{violet}} \approx \frac{4.97 \times 10^{-19} \, \text{J}}{1.602 \times 10^{-19} \, \text{J/eV}} \approx 3.11 \, \text{eV} \)[/tex]

[tex]\( E_{\text{red}} \approx \frac{2.83 \times 10^{-19} \, \text{J}}{1.602 \times 10^{-19} \, \text{J/eV}} \approx 1.77 \, \text{eV} \)[/tex]

Learn more about photons here:

https://brainly.com/question/29415147

#SPJ11

If the scale reads zero, this means there is no normal force acting on the student, and they are in free-fall. The student should indeed be worried, as the elevator is likely in a state of mechanical failure and is falling freely.

The first step is to draw a free-body diagram for the student and the elevator. There are two forces acting on the elevator-student system: the force of gravity (weight) and the force of tension from the cable. When the elevator is moving, there is also an additional force of acceleration.

(a) To find the acceleration of the elevator when the scale reads 450 N, we need to use Newton's second law, which states that the net force acting on an object is equal to its mass times its acceleration: F_net = ma. In this case, the net force is the difference between the weight and the tension: F_net = weight - tension. So we have:

F_net = ma
weight - tension = ma

Substituting the given values:

550 N - 450 N = (850 kg)(a)

Solving for a:

a = 1.18 m/s^2, upward (because the elevator is moving upward)

(b) To find the acceleration of the elevator when the scale reads 670 N, we use the same formula:

F_net = ma
weight - tension = ma

Substituting the given values:

550 N - 670 N = (850 kg)(a)

Solving for a:

a = -0.14 m/s^2, downward (because the elevator is moving downward)

(c) If the scale reads zero, it means that the tension in the cable is equal to the weight of the elevator-student system, so there is no net force and no acceleration. The student does not need to worry, but they may feel weightless for a moment if the elevator is in free fall.

(a) When the scale reads 450 N, we can determine the acceleration of the elevator using the following steps:

1. Calculate the net force acting on the student: F_net = F_gravity - F_scale = 550 N - 450 N = 100 N.
2. Use Newton's second law (F = ma) to find the acceleration: a = F_net / m_student, where m_student = 550 N / 9.81 m/s² ≈ 56.1 kg.
3. Solve for the acceleration: a = 100 N / 56.1 kg ≈ 1.78 m/s², downward.

(b) If the scale reads 670 N, follow the same steps as before, but replace F_scale with the new reading:

1. Calculate the net force: F_net = F_gravity - F_scale = 550 N - 670 N = -120 N.
2. Solve for the acceleration: a = F_net / m_student = -120 N / 56.1 kg ≈ -2.14 m/s², upward.

To know more about acceleration visit:-

https://brainly.com/question/30660316

#SPJ11

The value of the temperature and volume are:

A. 270 K

B. 360 K

C. 0.347 J

D. 373.347 J

E. 373 J

To solve this problem, we can use the ideal gas law, PV = nRT, where P is pressure, V is volume, n is the number of moles, R is the gas constant, and T is temperature.

A. To find the initial temperature, we can rearrange the ideal gas law as T = PV/nR and plug in the given values:

T = (2.90 atm)(3.20×10−2 m3)/(3 mol)(8.31 J/mol·K) = 270 K

B. To find the final temperature, we can again use the ideal gas law, but this time with the final volume:

T = (2.90 atm)(4.30×10−2 m3)/(3 mol)(8.31 J/mol·K) = 360 K

C. The amount of work the gas does in expanding is given by the equation W = PΔV, where ΔV is the change in volume:

W = (2.90 atm)(4.30×10−2 m3 - 3.20×10−2 m3) = 0.347 J

D. The amount of heat added to the gas can be found using the first law of thermodynamics, which states that ΔU = Q - W, where ΔU is the change in internal energy and Q is the heat added:

ΔU = (3/2)nRΔT = (3/2)(3 mol)(8.31 J/mol·K)(360 K - 270 K) = 373 J

Q = ΔU + W = 373 J + 0.347 J = 373.347 J

E. The change in internal energy of the gas is given by the equation ΔU = (3/2)nRΔT:

ΔU = (3/2)(3 mol)(8.31 J/mol·K)(360 K - 270 K) = 373 J

To know more about temperature,

https://brainly.com/question/29072206

#SPJ11

At equal pressure, less lp(liquefied petroleum) gas will flow through an orifice than natural gas. False.

At equal pressure, LP (liquefied petroleum) gas will generally flow through an orifice more easily than natural gas. This is due to the differences in the physical properties of the two gases.

LP gas, such as propane or butane, is stored in a liquid state under pressure. When the pressure is released, it vaporizes and becomes a gas. As a result, LP gas has a higher energy content and a higher vapor pressure compared to natural gas.

On the other hand, natural gas primarily consists of methane and is typically supplied through pipelines. It is in a gaseous state at normal atmospheric conditions.

When an orifice or a restricted opening is present, the flow rate of gas is determined by several factors, including the pressure difference across the orifice, the size of the orifice, and the properties of the gas.

Given equal pressure conditions, LP gas will tend to flow more readily through an orifice compared to natural gas. This is because LP gas has a higher vapor pressure, which means it has a greater tendency to expand and fill the available space. The higher energy content of LP gas also contributes to its ability to flow more easily through the orifice.

Therefore, the statement that less LP gas will flow through an orifice than natural gas at equal pressure is false. LP gas is expected to flow more readily through the orifice compared to natural gas.

To know more about natural gas, please click on:

https://brainly.com/question/12200462

#SPJ11

The magnetic field amplitude of the electromagnetic wave from the 15W point source is 0.60 μT at a distance of 2.10 m.

To solve this problem, we can use the equation for the magnetic field amplitude (B) of an electromagnetic wave at a certain distance (r) from the source:

B = (μ0/4π) * (2πf) * (r^-1) * E

where μ0 is the permeability of free space (4π x 10^-7 T·m/A), f is the frequency of the wave, E is the electric field amplitude, and r is the distance from the source.

We are given that the source has a power output of 15W, but we do not know the frequency of the wave or the electric field amplitude. However, we do know that the magnetic field amplitude at a certain distance is 0.60 μT. So we can rearrange the equation to solve for r:

r = (μ0/4π) * (2πf) * (E/B)

We can assume that the frequency of the wave is constant, so we can combine the constants in the equation and substitute the values:

r = (1.26 x 10^-6 m) * (E/B)

We need to find the value of r that makes B = 0.60 μT. Let's assume that E is also constant and solve for r:

r = (1.26 x 10^-6 m) * (E/0.60 x 10^-6 T)

r = 2.10 m.

Learn more about electromagnetic wave at: https://brainly.com/question/13803241

#SPJ11

Since aluminum has a higher coefficient of thermal expansion, it will reach its expansion limit first. Therefore, the gap will close at -72.27°C.

To solve this problem, we need to use the coefficient of thermal expansion for each material. Brass has a coefficient of 18.7 x 10^-6 m/m°C, while aluminum has a coefficient of 23.1 x 10^-6 m/m°C.
Assuming that both bars are initially at the same temperature, the gap between them will increase or decrease depending on which bar expands or contracts more. Since aluminum has a higher coefficient of thermal expansion, it will expand more than brass as the temperature increases.
To find the temperature at which the gap is closed, we can use the formula ΔL = αLΔT,
where ΔL is the change in length, α is the coefficient of thermal expansion, L is the original length, and ΔT is the change in temperature.

We know that the gap between the bars is 1.67 x 10^-3 m at 24.3 °C. Let's assume that the gap is closed when the bars touch each other. In other words, ΔL = -1.67 x 10^-3 m.

Let's also assume that the bars are each 1 meter long.
For aluminum:
-ΔL = αLΔT
-1.67 x 10^-3 m = (23.1 x 10^-6 m/m°C)(1 m)ΔT
ΔT = -72.27°C

For brass:
ΔL = αLΔT
1.67 x 10^-3 m = (18.7 x 10^-6 m/m°C)(1 m)ΔT
ΔT = 89.12°C

It's important to note that this calculation assumes that the bars are free to expand and contract. However, since they are attached to an immovable wall, there may be additional stresses and strains that could affect the outcome.

To know more about thermal expansion visit:

https://brainly.com/question/30242448

#SPJ11

a) The value of α = 2.30 [rad/s²]

b) The value of τ = 0.00943 Nm.

A) We can use the formula for torque τ = Iα, where I is the moment of inertia and α is the angular acceleration. Since the disk has uniform mass distribution, we can use the formula for moment of inertia of a solid disk rotating about its center:

I = (1/2)MR²,

where M is the mass of the disk and R is the radius.

We can find R by dividing the diameter by 2:

R = 19.6 cm / 2

= 0.098 m.

The mass of the disk is not given, so we cannot calculate the moment of inertia directly. However, we are given the linear acceleration a of a mass dropped from rest on the disk. If we assume that the disk rotates as a result of the torque from the falling mass, we can relate the linear acceleration a to the angular acceleration α by the formula a = Rα. Solving for α, we get:

α = a/R

= 0.225 [ms⁻²] / 0.098 [m]

= 2.30 [rad/s²]

Therefore, α is 2.30 [rad/s²].

B) Now that we have found α, we can use the mass of the dropping object and the formula for torque τ = Iα to calculate the torque. The moment of inertia I is still (1/2)MR², and we can find M by dividing the mass of the dropping object by the fraction of the mass that is expected to be accelerated, which is (1/2) since the mass is dropped at the edge of the disk.

So, M = 2m

= 2(0.210 kg)

= 0.420 kg.

Putting this all together, we get:

τ = Iα

τ = (1/2)MR² α

τ = (1/2)(0.420 kg)(0.098 m)²(2.30 [rad/s²])

τ = 0.00943 Nm

Therefore, τ is 0.00943 Nm.

To learn more about acceleration, here

https://brainly.com/question/12550364

#SPJ4

To find out how many feet per hour light travels, we need to convert miles per second to feet per hour. There are 5280 feet in a mile and 60 minutes in an hour, so we can use the following formula:

186,283 miles/second * 5280 feet/mile * 60 seconds/minute * 60 minutes/hour = 671,088,960,000 feet/hour

Therefore, light travels at approximately 671 billion feet per hour.

This is an incredibly fast speed, and it is important to note that nothing can travel faster than the speed of light. The speed of light has a profound impact on our understanding of the universe and has led to many scientific breakthroughs, including the theory of relativity. Understanding the properties of light and how it interacts with matter is crucial for fields such as optics, astronomy, and physics.

To know more about properties of light click this link-

brainly.com/question/9601852

#SPJ11

The electron is moving at approximately 5.27 × 10^(-25) m/s (or 0.527 × 10^(-24) m/s) based on the given uncertainty in its speed.

The uncertainty principle states that there is a fundamental limit to how precisely we can know both the position and momentum of a particle. In the case of the ground state of hydrogen, if the uncertainty in the position of the electron is approximately 0.10 nm, we can use this information to estimate the uncertainty in its speed.

The uncertainty in the position (∆x) and the uncertainty in the momentum (∆p) are related by the following inequality: ∆x * ∆p ≥ h/4π, where h is the Planck constant.

Assuming the uncertainty in the position (∆x) is 0.10 nm (which is equivalent to 0.10 × 10^(-9) meters), we can rearrange the uncertainty principle equation to solve for the uncertainty in momentum (∆p). The equation becomes: ∆p ≥ h / (4π * ∆x).

Plugging in the values, we have: ∆p ≥ (6.626 × 10^(-34) J·s) / (4π * 0.10 × 10^(-9) m).

The uncertainty in momentum (∆p) is approximately equal to the uncertainty in the speed of the electron. So, we can use ∆p as an estimate of the electron's speed.

Calculating this, we get: ∆p ≥ 5.27 × 10^(-25) kg·m/s.

Learn more about electron  here:-

https://brainly.com/question/12001116

#SPJ11

The correct answer is "They commonly live under extreme temperature and salinity." This is one of the defining features of archaea that sets them apart from other groups of organisms.

While some archaea do have cell membranes and some are multicellular, these characteristics are not unique to this group and can be found in other organisms as well. The absence of a cell nucleus is also a distinguishing feature of archaea, but this was not included in the options provided.
The distinct feature that makes archaea different from other groups of organisms is that they commonly live under extreme temperature and salinity conditions. Archaea are unique due to their ability to thrive in environments that are inhospitable to most other life forms. While they do have cell membranes, this is not the main feature that sets them apart, as other organisms also have cell membranes. Additionally, archaea do not have a cell nucleus and are not multicellular organisms, which further differentiates them from some other groups.

For more such questions on archaea , Visit:

https://brainly.com/question/30218861

#SPJ11

The system with the extrasolar planet that is easiest to detect from Earth would likely be System A, as it has the largest planet with the shortest orbital period.

This would result in the planet passing in front of its host star more frequently, causing noticeable dips in the star's brightness that can be detected by telescopes on Earth. For example, a large planet close to its star will be easier to detect through the radial velocity method, which measures the wobble of the star caused by the gravitational pull of the planet. On the other hand, a smaller planet farther from its star may be easier to detect through the transit method, which measures the slight dip in the star's brightness as the planet passes in front of it.

Additionally, the planet's large size would make it easier to detect using methods such as radial velocity measurements. The detectability of an exoplanet depends on several factors, including its size, mass, orbital distance, and the method used for detection.

To know more about planet refer here :

https://brainly.com/question/30395625

#SPJ11

The electric potential energy of the charge is 2.7 J. The formula to calculate electric potential energy is U = q × V, where U is the potential energy, q is the charge, and V is the electric potential. Plugging in the given values, U = (4.5 × 10^-5 C) × (2.0 × 10^4 N/C) × (0.030 m) = 2.7 J.

The electric potential energy (U) of a charged object in an electric field is given by the formula U = q × V, where q is the charge of the object and V is the electric potential at the location of the object.

In this case, the charge (q) is 4.5 × 10^-5 C, and the electric field strength (V) is 2.0 × 10^4 N/C. The distance of the charge from the source of the electric field is given as 0.030 m.

Plugging in the values into the formula, we have U = (4.5 × 10^-5 C) × (2.0 × 10^4 N/C) × (0.030 m). Simplifying the expression, we get U = 2.7 J.

Therefore, the electric potential energy of the charge is 2.7 Joules.

learn more about electric  here:

https://brainly.com/question/31173598

#SPJ11

The motor speed when the load draws an armature current of 30 A can be calculated using the speed formula for a DC shunt motor:

[tex]N2 = N1 * (I1 / I2)[/tex]

Where:

N1 = Speed at unloaded condition = 1000 rpm

I1 = Armature current at unloaded condition = 3 A

I2 = Armature current at loaded condition = 30 A

Plugging in the values, we have:

[tex]N2 = 1000 * (3 / 30) = 100 rpm[/tex]

ii. For a constant-torque load, the speed can be calculated using the formula:

[tex]N2 = N1 * (√(R1 + Ra) / √(R2 + Ra))[/tex]

Where:

R1 = Total resistance in the armature circuit without additional resistance = armature resistance (1.5 Ω)

R2 = Total resistance in the armature circuit with additional resistance (3 Ω)

Ra = Field resistance = 600 Ω

N1 = Speed at unloaded condition = 1000 rpm

Plugging in the values, we have:

[tex]N2 = 1000 * (√(1.5 + 600) / √(3 + 600)) = 976 rpm[/tex]

iii. To calculate the motor speed when the field is reduced by 10%, we can use the formula:

[tex]N2 = N1 * (V2 / V1)[/tex]

Where:

N1 = Speed at unloaded condition = 1000 rpm

V1 = Voltage applied to the motor = 600 V

V2 = Voltage applied to the motor with reduced field = 600 V - (10% of 600 V) = 540 V

Plugging in the values, we have:

[tex]N2 = 1000 * (540 / 600) = 900 rpm[/tex]

i. When the load draws an armature current of 30 A, the motor speed decreases to 100 rpm. This is because an increase in armature current leads to increased electromagnetic forces, which counteract the motion and slow down the motor.

ii. When a 3 V resistance is added to the armature circuit, the motor speed decreases to 976 rpm. The additional resistance increases the total resistance in the armature circuit, causing a voltage drop and reducing the speed.

iii. If the field is reduced by 10%, the motor speed decreases to 900 rpm. The reduction in field current weakens the magnetic field, reducing the electromagnetic forces and hence the speed of the motor.

learn more about motor here:

https://brainly.com/question/12989675

#SPJ11

Answer:

Explanation:

The final temperature after doubling both the pressure and volume of helium gas, initially at a volume of 2.90 L, a pressure of 0.160 atm, and a temperature of 45.0 °C, is 1272.6K and 0.071 grams of helium are present.

We know that using the combined gas law equation:

[tex]\frac{(P1 * V1)}{T1} = \frac{(P2 * V2)}{T2}[/tex]

Substituting the given values:

[tex]\frac{(0.160 atm * 2.90 L)}{318.15 K} = \frac{(2 * 0.160 atm *2* 2.90 L)}{T2}[/tex]

[tex]T2 = 318.15*4 K[/tex]

[tex]T2 = 1272.6 K\\[/tex]

Therefore the final temperature is 1272.6K.

To calculate the number of moles of helium we can use the ideal gas law equation:

PV = nRT

Substituting the given values:

(0.320 atm) * (5.80 L) = n * (0.08206 L atm / K mol) * (1272.6) K

n = 0.0177 moles

Finally, we can use the relationship between moles, mass, and molar mass:

mass = moles * molar mass

mass = 0.0177* 4 grams

mass = 0.071 grams

Therefore, there are approximately 0.071 grams of helium in the given sample.

To learn more about combined gas law,

https://brainly.com/question/13154969

The output frequency of a MOD 15 counter with a 30 kHz clock pulse is 2.0 kHz.

To find the output frequency, first, we need to understand that a MOD 15 counter has 15 states (0 to 14), meaning it takes 15 clock pulses to complete one cycle. Next, we'll divide the input frequency by the number of states to find the output frequency:
Input frequency: 30 kHz
Number of states: 15
Output frequency = (Input frequency) / (Number of states) = (30 kHz) / (15) = 2 kHz
Therefore, the output frequency is 2.0 kHz, which corresponds to option C.

Learn more about frequency here:

https://brainly.com/question/14320803

#SPJ11

A suitable combination of R = 500 Ω and C = 3.31 μF can be used to design the required RC low-pass filter.

The transfer function of an RC low-pass filter is given by:

H(jω) = 1 / [1 + jωRC]

where H(jω) is the complex gain of the filter at frequency ω, R is the resistance in ohms, and C is the capacitance in farads.

To design a filter that attenuates a 120 Hz sinusoidal voltage by 20 dB with respect to the DC gain, we need to find the cutoff frequency ωc at which the gain of the filter is 20 dB below the DC gain.

The DC gain of the filter is given by:

|H(j0)| = 1 / (1 + j0RC) = 1

The gain at frequency ω is given by:

|H(jω)| = 1 / √[1 + (ωRC)^2]

Setting |H(jω)| = 1/√2 (i.e., 20 dB attenuation), we get:

1/√2 = 1 / √[1 + (ωcRC)^2]

Solving for ωc, we get:

ωc = 1 / (RC√[2] ) = 1 / (500 × 3.1416 × 3.25 × 10^-6 × √[2]) ≈ 120 Hz

Therefore, the cutoff frequency of the filter should be approximately 120 Hz.

To implement the filter, we can use a 500 Ω resistor and a capacitor with a value of:

C = 1 / (2π × 500 × 120) ≈ 3.31 μF

For more question on RC low-pass filter click on

https://brainly.com/question/28832912

#SPJ11

To design an RC low-pass filter that attenuates a 120 Hz sinusoidal voltage by 20 dB with respect to the DC gain, we need to calculate the values of the resistor and capacitor. The formula for the cut-off frequency (fc) of the filter is fc = 1/(2πRC), where R is the resistance value and C is the capacitance value.

We can rearrange this formula to solve for either R or C.
Assuming we have a standard capacitor value of 0.1 uF, we can solve for the resistor value as follows:
fc = 120 HzHz
RC = 1/(2πfc) = 1/(2π*120*0.1*10^-6) ≈ 13.2 kΩ
Using a 500 Ω resistor, we can calculate the necessary capacitance as:
C = 1/(2π*120*500) ≈ 2.1 uF

Therefore, the RC low-pass filter can be designed with a 500 Ω resistor and a 2.1 uF capacitor. This filter will attenuate a 120 Hz sinusoidal voltage by 20 dB with respect to the DC gain.

To learn more about low-pass filter click here:brainly.com/question/31477383

#SPJ11

Number of slits per mm = 1 / 0.001279 mm ≈ 782 slits/mm, the spacing, d, between the slits we can use the equation for the diffraction grating:
d sinθ = mλ

We are given λ = 532 nm and θ = 25° for the first-order maximum. Therefore, we can solve for d: d = mλ/sinθ
For the first-order maximum, m = 1. Plugging in the values, we get:
d = (1)(532 nm)/sin(25°) ≈ 1223 nm
So the spacing between the slits is approximately 1223 nm.
To find the number of slits per mm, we can use the formula: n = 1/d
Where n is the number of slits per unit length.

We want the answer in units of mm, so we convert nm to mm:                        1 nm = 10^-6 mm
where n is the order of the maximum (n = 1 for the first-order maximum), λ is the wavelength of the laser (λ = 532 nm), and θ is the angle (θ = 25°). Rearranging the formula to solve for d, we get: d = (n * λ) / sin(θ)
Substitute the values:
d = (1 * 532 nm) / sin(25°)
d ≈ 1279 nm
Now, to find the number of slits per mm, we simply need to convert the spacing to mm and take its reciprocal:
d = 1279 nm = 0.001279 mm

To know more about diffraction visit:-

https://brainly.com/question/12290582

#SPJ11

Explanation:

Power = work / time

  9      =  45/ t

t = 45/9 = 5 seconds

The work done by the normal force on the mass during the initial fall is : zero.

The normal force acts perpendicular to the displacement of the mass. In this case, during the initial fall, the displacement of the mass is vertical downward, while the normal force acts perpendicular to the surface supporting the mass. Since the normal force and displacement are perpendicular to each other, the work done by the normal force is zero.

Work is defined as the dot product of the force and the displacement, given by the equation:

[tex]\text{Work} = \text{force} \times \text{displacement} \times \cos(\text{angle})[/tex]

In this case, the angle between the normal force and the displacement is 90 degrees, and the cosine of 90 degrees is zero. Therefore, the work done by the normal force is zero.

To know more about the work done refer here :

https://brainly.com/question/29989410#

#SPJ11

The strength and conditioning professional should use the formula "Work / time" to calculate power when comparing the power produced by two athletes performing the back squat.

To calculate power in the context of comparing the power produced by two athletes performing the back squat, the strength and conditioning professional should use the formula "Work/time." Power is defined as the rate at which work is done or energy is transferred. Work is calculated by multiplying force by the distance moved, and time represents the duration of the exercise. Dividing the work done during the back squat by the time taken gives the power generated. This formula allows for a quantitative comparison of the power output between athletes by considering both the work performed and the time taken to perform it.

Learn more about back squat here:

https://brainly.com/question/13151659

#SPJ11

The amount of heat required to evaporate 20 g of water at 100 °C is 10,800 calories and the amount of heat required to convert 28 g of ice at -16 °C to 24 °C into liquid water is 3,136 calories.

What is heat?

Heat is a form of energy that is transferred between objects or systems due to temperature differences. It is the energy that flows from a higher temperature object to a lower temperature object.

Q = m * H

Q = 20 g * 540 cal/g

Q = 10,800 cal

Therefore, the amount of heat required to evaporate 20 g of water at 100 °C is 10,800 calories.

     2. Heating 28 g of ice from -16 °C to 24 °C until it becomes liquid water:

First, calculate the heat required to raise the temperature of the ice from -16 °C to 0 °C:

Q1 = m * C * ΔT

Q1 = 28 g * 0.5 cal/g °C * (0 °C - (-16 °C))

Q1 = 224 cal

Next, calculate the heat required to melt the ice at 0 °C:

Q2 = m * H

Q2 = 28 g * 80 cal/g

Q2 = 2,240 cal

Then, calculate the heat required to raise the temperature of the water from 0 °C to 24 °C:

Q3 = m * C * ΔT

Q3 = 28 g * 1 cal/g °C * (24 °C - 0 °C)

Q3 = 672 cal

Total heat = Q1 + Q2 + Q3

Total heat = 224 cal + 2,240 cal + 672 cal

Total heat = 3,136 cal

Therefore, the amount of heat required to convert 28 g of ice at -16 °C to 24 °C into liquid water is 3,136 calories.

To learn more about heat,

https://brainly.in/question/54170243

#SPJ4

The approximate temp. (k) at which 15% of the molecules will be in the upper state is 200 (Option C).

To find the approximate temperature at which 15% of the molecules will be in the upper state, we can use the Boltzmann distribution formula:

n_upper/n_total = exp(-ΔE / kT)

Where n_upper is the number of molecules in the upper state, n_total is the total number of molecules, ΔE is the energy difference between the states (360 cm⁻¹), k is the Boltzmann constant (0.695 cm⁻¹ K⁻¹), and T is the temperature in Kelvin.

Since we're looking for the temperature at which 15% of the molecules will be in the upper state, n_upper/n_total = 0.15. Plugging this into the formula, we get:

0.15 = exp(-360 / (0.695 × T))

Solving for T, we get an approximate temperature of:

T ≈ 200 K

Therefore, the correct answer is (C) 200.

You can learn more about molecules at: brainly.com/question/30465503

#SPJ11

when the two charged bodies are moved to be one-fourth as far apart, the force exerted between them increases to 2.32 N.

When two charged bodies are moved so that they are one-fourth as far apart, the force exerted between them can be found using the inverse square law for electrostatic force. The formula for this law is:

F_new = F_old * (d_old / d_new)^2

Given that the initial force, F_old, is 0.145 N and the distance is reduced to one-fourth (d_new = 1/4 * d_old), we can plug these values into the formula:

F_new = 0.145 * (1 / (1/4))^2

F_new = 0.145 * (4)^2

F_new = 0.145 * 16

F_new = 2.32 N

Therefore, the force between the two charged bodies increases to 2.32 N when they are shifted to be one-fourth as apart. This outcome emphasizes how Coulomb's law, which states that the force between two charged things is inversely proportional to the square of their distance, is an example of an inverse square law. The force exerted by the charged bodies on one another grows quickly as the distance between them shrinks.

To know more about Coulomb's law, click here;

https://brainly.com/question/506926

#SPJ11